The through dovetail joint is the most popular dovetail joint because it is strong, attractive, and versatile. It is commonly used in furniture-making, cabinetry, and woodworking. The through dovetail joint is a traditional woodworking joint characterized by the interlocking triangular shape it creates.
What is a standard dovetail?
Standard Size Dovetails. A standard size dovetail is as tall as your lumber is thick. This assumes you are joining boards of the same thickness with through-dovetails and that you intend to have them flush with the finished corner surfaces on both legs of the corner.
What is the most popular dovetail?
Single-lap Dovetail The single-lap (known to many folks as a half-blind dovetail) is the best known of the dovetails since it’s used to join the front to the sides of a drawer.
What is an English dovetail joint?
English Dovetail / Through Dovetail The craftsperson usually orients the tails and pins in this joint horizontally, although this isn’t a cardinal rule. It is sometimes called a through dovetail because both the pins and tails go all the way through each-other.
What is the difference between English dovetail and French dovetail?
English dovetails are the most common. They have interlocking joints and allow the most amount of space – usually several more inches of room than you would get with French dovetails. This is because the dovetail groove cannot be put all the way at the edge of a drawer with French dovetails.
What is the strongest joint in woodworking?
Mortise and tenon joints have stood the test of time for their remarkable strength. This traditional joint involves a projecting piece of wood, called a tenon, securely fitting into a corresponding cavity, a mortise. It can be reinforced with glue or wedges for stability for a stronger hold.
Are dovetail joints worth it?
Making sure that you pick a drawer joint that can withstand this type of wear and tear is crucial to the longevity of your kitchen cabinets. Dovetail joints are considered one of the strongest joints used in kitchen cabinetry construction and are the best solution for a kitchen cabinet drawer box.
Should you glue dovetail joints?
Michael Dresdner: The only areas that require glue on dovetails are the diagonal faces. All the diagonal faces are long grain, all the square faces are end grain, and all the flat faces abut end grain. Therefore, you need only apply glue to the diagonal faces on the tails or pins, or both.
What is a French dovetail joint?
Fyi, the English dovetail technique is also commonly referred to as a butt joint. French Dovetail: This technique is based on cutting out a slat in the middle of a board and also a corresponding piece of wood that can slide into the middle cutout. English and French Dovetail Drawer Construction.
What are 2 disadvantages of using dovetail joints?
The disadvantages of dovetail joints are that they can be fairly difficult to mark out and cut, and if they are made badly these joints lose the advantages listed above. Depending on the project, function, and design, there are a number of different types of dovetail joints to choose from.
Are dovetail joints still used?
Dovetail joints used to be the best way to join pieces of wood, especially a box or drawer. I used to cut them by hand but now you can buy jigs. Modern glues, like Gorilla Glue, are so strong I rarely use a dovetail joint unless it’s going to show. I usually use a rabbet, or sometimes even a butt joint.
What is the difference between 11mm and 3 8 dovetail?
The 3/8 Inch is measured across the bottom of the dovetail whereas the 11 mm is measured across the top of the dovetail. A 3/8 Inch dovetail is about 12.7 mm across the top. The measurements 3/8 and 11mm are not the same for this reason plus the angles are different.
What is stronger dovetail or finger joint?
Although the finger joint is not mechanically interlocking like a dovetail, the joint is amazingly strong. Today’s modern adhesives and the large glue surface make the finger joint equally as strong as the dovetail throughout the life of the adhesive.
What size is a standard dovetail rail?
Dovetails come in several different types and sizes depending on manufacturer, but the most common are the 11 mm and 3⁄8 inch (9.5 mm). Some other less known, but currently commercially available dovetail mounts, are 12, 13, 13.5, 14, 14.5, 16, 16.5, 17 and 19 mm.
What is the standard dovetail ratio?
Dovetail angles are usually expressed as ratios — the most common being 1:6 and 1:8 (said “one in eight,” and also written as 6:1 or 8:1). As a general rule of thumb: Use 1:6 for softwoods. Use 1:8 for hardwoods.
Is 11mm dovetail the same as 3 8?
However, that is not the only difference between the two dovetails. They also have different groove angles as shown below. The 11 mm dovetail has a 60-degree angle, while the 3/8” dovetail has a 45-degree angle.
What is the difference between 11mm and 3 8 dovetail?
The 3/8 Inch is measured across the bottom of the dovetail whereas the 11 mm is measured across the top of the dovetail. A 3/8 Inch dovetail is about 12.7 mm across the top. The measurements 3/8 and 11mm are not the same for this reason plus the angles are different.
How do you date a dovetail joint furniture?
You can get an idea of the date of a piece of antique furniture by looking at the dovetail joint, as if it is hand cut you know its pre 1880 and the more primitive the cut usually means an earlier piece. Below you can see examples, the first is a 17th century drawer, pre dovetail so very primitive clout nails used.
What joint is often used for shelving?
Dado Joint This simple joint is often utilized for furniture building, such as shelving, cabinetry, and drawer dividers.
What size dovetail should I use?
Your tails should be around 18mm > 35mm for fine work like drawers and 35mm > 55mm on larger work like a chest.
What is the difference between Martin simple dovetail and dovetail?
Martin’s traditional dovetail is a compound dovetail. It is more suited to hand fitting, and that is how Martin does it. Their new Simple Dovetail is a straight dovetail that has been adapted to CNC fitting.
What is the best dovetail angle?
The ideal, he says, is 8.5° for softwoods and 7.5° when joining hardwoods. One Wednesday morning I laid out and cut a bunch of these dovetails. I ignored the really shallow angles (6.5° to 8.5°) because I wanted to adopt something more angular. The 10° dovetails looked OK.
What is the weakest joint in carpentry?
The butt joint is the simplest joint. An unreinforced butt joint is also the weakest joint, as it provides a limited surface area for gluing and lacks any mechanical interlocking to resist external forces.
What is the weakest type of woodworking joint?
A butt joint uses a simple technique whereby two pieces of material are joined together at their ends, without any special shaping or cutting. Although it is simple, the butt joint is also the weakest of the wood joinery types.
What is the most popular wood joint?
Pocket-hole joinery is one of the most popular woodworking joinery methods and is well suited for beginners and professionals alike. At the heart, this is a butt joint that’s been reinforced with screws. The pocket-hole joint requires forming an angled hole/slot located close to the end of a board.
What is an impossible dovetail joint?
Press a dovetailed board into another board with matching sockets, and you’ve created woodworking’s most iconic joint. The dovetails and sockets wedge the boards together, so the joint can’t pull apart; the only way to disassemble it is to lift the dovetailed board back out of the sockets.
