Dovetail angles are usually expressed as ratios — the most common being 1:6 and 1:8 (said “one in eight,” and also written as 6:1 or 8:1). As a general rule of thumb: Use 1:6 for softwoods. Use 1:8 for hardwoods.Dovetail angles are usually expressed as ratios — the most common being 1:6 and 1:8 (said “one in eight,” and also written as 6:1 or 8:1). As a general rule of thumb: Use 1:6 for softwoods. Use 1:8 for hardwoods.
What ratio is a 14 degree dovetail?
This 14° marker equates to a ratio of 1:4. When used with thinner stock, the 14° angle results in a better looking joint. This different angle also gives you a slightly stronger dovetail interlock on the thinner material.
What is a 6 to 1 dovetail?
The left-hand photo shows the “ratio” method to layout the angle of your dovetails. (I used SketchUp to draw and show the angles.) A 1:6 ratio – that’s one unit horizontal with six matching units drawn vertical – lays out as a 9.5 degree angle.
What is a standard dovetail?
The dovetail joint drawers are typically used to link the edges of a drawer to the front and are known for their tensile strength to being pushed apart. Pins or tongues cut from one board’s end interlock with the groove or tail on the other board’s end.
What is a 6 to 1 dovetail?
The left-hand photo shows the “ratio” method to layout the angle of your dovetails. (I used SketchUp to draw and show the angles.) A 1:6 ratio – that’s one unit horizontal with six matching units drawn vertical – lays out as a 9.5 degree angle.
What is the most common dovetail angle?
Percy Blandford, who has been writing about woodworking for a long time, writes in “The Woodworker’s Bible” that any angle between 7.5° and 10° is acceptable. The ideal, he says, is 8.5° for softwoods and 7.5° when joining hardwoods.
What are common dovetail sizes?
Dovetails come in several different types and sizes depending on manufacturer, but the most common are the 11 mm and 3⁄8 inch (9.5 mm). Some other less known, but currently commercially available dovetail mounts, are 12, 13, 13.5, 14, 14.5, 16, 16.5, 17 and 19 mm.
Is 11mm dovetail the same as 3 8?
However, that is not the only difference between the two dovetails. They also have different groove angles as shown below. The 11 mm dovetail has a 60-degree angle, while the 3/8” dovetail has a 45-degree angle.
What is the minimum thickness for a dovetail?
Structurally I have looked for pin strength in dovetails as the dovetailed aspect is always strong because it is always at least as wide and mostly wider than the pins. In my own work I aim for a minimum size of 1/4″ and mostly 3/8″.
What is the difference between 11mm and 3 8 dovetail?
11mm rings use a 60 degree dovetail and are measured at the top. 3/8″ rings use a 45 degree dovetail and are measured at the bottom.
What is an English dovetail joint?
A dovetail joint is a locking joint. The English dovetail construction tends to allow for the largest possible drawer storage capacity. French dovetail construction is used for more elaborate features such a curved, bowed design.
Should you glue dovetail joints?
Michael Dresdner: The only areas that require glue on dovetails are the diagonal faces. All the diagonal faces are long grain, all the square faces are end grain, and all the flat faces abut end grain. Therefore, you need only apply glue to the diagonal faces on the tails or pins, or both.
Which is better English or French dovetail?
While both English and French dovetail construction are very sturdy and high quality, English dovetail construction is slightly sturdier with the trade-off of being more expensive and time-consuming to produce.
What angle is a 1 in 8 dovetail?
It would be extremely difficult to be able to pick these differences up in your dovetails on a piece of furniture by eye. So in closing your 1:4 Saddle-Tail is for all practical purposes 14 degrees, the 1:6 is close to 10 degrees and the 1:8 is about 7 degrees.
What is the slope of a dovetail joint?
There are different types of dovetail joints. The angle of slope varies according to the wood used, purpose of joint and type of work. Typically the slope is 1:6 for softwoods, and a shallower 1:8 slope for hardwoods. Often a slope of 1:7 is used as a compromise.
What angle should a dovetail joint be?
The angle of a dovetail joint should be between 7 and 15 degrees: too broad and the joint won’t be strong enough, too skinny, and the pin can snap. So the angle of the dovetail mainly depends on the use and wear the joint will get. 5. They are called ‘dovetails’ because they are shaped like the tail feathers of a dove!
What are typical dovetail angles?
Although softwoods are more compressible than hardwoods, you needn’t change the dovetail angle to add strength to the joint. Any angle between 7° and 15° will work, regardless of the wood. But stay within that range. If you go below 7°, you’ll start to lose the mechanical strength of the dovetail.
What is a 6 to 1 dovetail?
The left-hand photo shows the “ratio” method to layout the angle of your dovetails. (I used SketchUp to draw and show the angles.) A 1:6 ratio – that’s one unit horizontal with six matching units drawn vertical – lays out as a 9.5 degree angle.
What are the traditional dovetail angles?
The angle of a dovetail joint should be between 7 and 15 degrees: too broad and the joint won’t be strong enough, too skinny, and the pin can snap. So the angle of the dovetail mainly depends on the use and wear the joint will get. 5. They are called ‘dovetails’ because they are shaped like the tail feathers of a dove!
What angle is a 1 in 8 dovetail?
It would be extremely difficult to be able to pick these differences up in your dovetails on a piece of furniture by eye. So in closing your 1:4 Saddle-Tail is for all practical purposes 14 degrees, the 1:6 is close to 10 degrees and the 1:8 is about 7 degrees.
What are the weaknesses of dovetail?
The disadvantages of dovetail joints are that they can be fairly difficult to mark out and cut, and if they are made badly these joints lose the advantages listed above. Depending on the project, function, and design, there are a number of different types of dovetail joints to choose from.
What are the rules for dovetail joints?
The general rule is that they measure half the thickness of timber plus around 1 mm along the shoulder line. So these two awl dots are 7 mm in from each edge. These two dots, which mark the corners of the half pins, are now converted into a 1:8 slope at each side.
What is the most popular dovetail joint?
The through dovetail joint is the most popular dovetail joint because it is strong, attractive, and versatile. It is commonly used in furniture-making, cabinetry, and woodworking. The through dovetail joint is a traditional woodworking joint characterized by the interlocking triangular shape it creates.
What size dovetail chisels do you really need?
Chisel Sizes – – 12mm / 1/2″ – This will do the majority of your morticing, and come in when cleaning out the pins on those dovetails. – 19mm / 3/4″ (or above) – A nice wide chisel is very useful, and I’d probably aim at an inch, though somewhere between 3/4″ – 1 1/4″ will fit the bill.
What makes a dovetail joint so strong?
The dovetail joint is very strong because of the way the ‘tails’ and ‘pins’ are shaped. This makes it difficult to pull the joint apart and virtually impossible when glue is added.
Is a finger joint stronger than a dovetail joint?
For box joint, some people put a lot more fingers than it is possible to do with Dovetail. In this case, the gluing surface is larger, and the joint is likely stronger. Also, some find a way to hide a finish nail in the joint. Dovetail has the advantage of a mechanical lock independent of the glue.
