A 1:6 ratio – that’s one unit horizontal with six matching units drawn vertical – lays out as a 9.5 degree angle. A 1:8 ratio – one unit horizontal with eight matching units drawn vertical – is an angle of 7.1 degrees.
What dovetail ratio is best?
With regard to what to use, a common recommendation is 1:8 for hardwoods and 1:6 for softwoods. These recommendations are based on some arguments related to strength. However, people use a lot of different ratios depending on application and aesthetics.
What ratio is a 14 degree dovetail?
This 14° marker equates to a ratio of 1:4. When used with thinner stock, the 14° angle results in a better looking joint. This different angle also gives you a slightly stronger dovetail interlock on the thinner material.
What is the angle of a 7 1 dovetail?
My go-to angle for through dovetails in most hardwoods is 7:1 (8.1°), such as for a carcase or box in cherry, maple, or walnut with stock thickness of 9/16″-13/16″. It has enough angle to form a strong mechanical lock but not too much to produce fragile tail corners or overly fussy fitting.
What are the measurements for a dovetail?
Fine work the pins 4mm > 6mm, larger work 7mm > 12mm. To have a desirable appearance the pins smaller than the tails. Your tails should be around 18mm > 35mm for fine work like drawers and 35mm > 55mm on larger work like a chest. Decide on your tail size remembering “One more tail than pin”.
What is the common dovetail ratio?
Dovetail angles are usually expressed as ratios — the most common being 1:6 and 1:8 (said “one in eight,” and also written as 6:1 or 8:1). As a general rule of thumb: Use 1:6 for softwoods. Use 1:8 for hardwoods.
Is 11mm dovetail the same as 3 8?
The 3/8 Inch is measured across the bottom of the dovetail whereas the 11 mm is measured across the top of the dovetail. A 3/8 Inch dovetail is about 12.7 mm across the top. The measurements 3/8 and 11mm are not the same for this reason plus the angles are different.
What is the most common dovetail angle?
Percy Blandford, who has been writing about woodworking for a long time, writes in “The Woodworker’s Bible” that any angle between 7.5° and 10° is acceptable. The ideal, he says, is 8.5° for softwoods and 7.5° when joining hardwoods.
What is a standard dovetail?
A series of pins cut to extend from the end of one board interlock with a series of ‘tails’ cut into the end of another board. The pins and tails have a trapezoidal shape. Once glued, a wooden dovetail joint requires no mechanical fasteners.
What is the minimum thickness for a dovetail?
In my own work I aim for a minimum size of 1/4″ and mostly 3/8″. Now that doesn’t mean I won’t go down to less or up too.
What are the traditional dovetail angles?
The angle of a dovetail joint should be between 7 and 15 degrees: too broad and the joint won’t be strong enough, too skinny, and the pin can snap.
Is dovetail 11mm?
Dovetails come in several different types and sizes depending on manufacturer, but the most common are the 11 mm and 3⁄8 inch (9.5 mm). Some other less known, but currently commercially available dovetail mounts, are 12, 13, 13.5, 14, 14.5, 16, 16.5, 17 and 19 mm.
What are typical dovetail angles?
Lower (7° to 9°) angles are often advised for joining hardwoods, while higher angles (10° to 14°) are recommended for softwoods and even higher angles (14° to 18°) for half-blind dovetails.
What are the rules for dovetail design?
As a rule of thumb the dovetail’s maximum width should occupy approximately 1/ 2 to 3/ 4 of the gasket’s width (leaving a 1/ 4 – 1/ 8 of gasket width on each side). For larger gasket widths, multiple dovetails can be made side-by- side, facing the same direction or inverted.
What is the most popular dovetail?
1) Through Dovetail Also known as the plain dovetail, this is the most common and basic type of dovetail joint. Through interlocking tails and pins, this joint showcases consistent angles, revealing the wood’s end grains on external surfaces.
Which is better English or French dovetail?
While both English and French dovetail construction are very sturdy and high quality, English dovetail construction is slightly sturdier with the trade-off of being more expensive and time-consuming to produce.
What is the most common dovetail angle?
Percy Blandford, who has been writing about woodworking for a long time, writes in “The Woodworker’s Bible” that any angle between 7.5° and 10° is acceptable. The ideal, he says, is 8.5° for softwoods and 7.5° when joining hardwoods.
What size is a standard dovetail rail?
Dovetails come in several different types and sizes depending on manufacturer, but the most common are the 11 mm and 3⁄8 inch (9.5 mm). Some other less known, but currently commercially available dovetail mounts, are 12, 13, 13.5, 14, 14.5, 16, 16.5, 17 and 19 mm.
Will 3 8 dovetail fit Picatinny rail?
3/8 Dovetail to Picatinny Adapter Rail -Short adaptor Rail attaches to 3/8 Dovetail rails and converts it to Picatinny Rail for mounting Red Dot optics with Weaver/Picatinny type rings and mounts.
What is a 3 8 dovetail?
3/8″ dovetail rails, sometimes call tip off rails, consist of two thin parallel grooves and are used almost exclusively on rimfire rifles and air rifles. 3/8″ dovetail rails are a common, standardized style within the rimfire industry and are inexpensive to machine into the firearm’s frame.
What degree is a 1 in 8 dovetail?
It would be extremely difficult to be able to pick these differences up in your dovetails on a piece of furniture by eye. So in closing your 1:4 Saddle-Tail is for all practical purposes 14 degrees, the 1:6 is close to 10 degrees and the 1:8 is about 7 degrees.
What are the weaknesses of dovetail?
The disadvantages of dovetail joints are that they can be fairly difficult to mark out and cut, and if they are made badly these joints lose the advantages listed above. Depending on the project, function, and design, there are a number of different types of dovetail joints to choose from.
Which is better English or French dovetail?
While both English and French dovetail construction are very sturdy and high quality, English dovetail construction is slightly sturdier with the trade-off of being more expensive and time-consuming to produce.
What is English dovetail?
English dovetails are the most common. They have interlocking joints and allow the most amount of space – usually several more inches of room than you would get with French dovetails. This is because the dovetail groove cannot be put all the way at the edge of a drawer with French dovetails.
What is a simple dovetail joint?
The simple dovetail neck joint is a timeless design that consists of a dovetail-shaped projection on the neck fitting into a corresponding recess in the guitar body. This joint provides a secure connection, facilitating good tonal transfer between the neck and body.
What is stronger dovetail or finger joint?
Although the finger joint is not mechanically interlocking like a dovetail, the joint is amazingly strong. Today’s modern adhesives and the large glue surface make the finger joint equally as strong as the dovetail throughout the life of the adhesive.
