Dovetail angles are usually expressed as ratios — the most common being 1:6 and 1:8 (said “one in eight,” and also written as 6:1 or 8:1). As a general rule of thumb: Use 1:6 for softwoods. Use 1:8 for hardwoods.
What dovetail angle is best?
Percy Blandford, who has been writing about woodworking for a long time, writes in “The Woodworker’s Bible” that any angle between 7.5° and 10° is acceptable. The ideal, he says, is 8.5° for softwoods and 7.5° when joining hardwoods.
What is the standard size of a dovetail?
11 mm and 3/8” dovetails are the two most common types of dovetails that you can find on rifles. The 11 mm dovetail represents a standard in Europe, while the 3/8” is a standard in the USA.
What is the standard dovetail ratio?
With regard to what to use, a common recommendation is 1:8 for hardwoods and 1:6 for softwoods. These recommendations are based on some arguments related to strength. However, people use a lot of different ratios depending on application and aesthetics.
What ratio for dovetail?
Dovetail angles are usually expressed as ratios — the most common being 1:6 and 1:8 (said “one in eight,” and also written as 6:1 or 8:1). As a general rule of thumb: Use 1:6 for softwoods. Use 1:8 for hardwoods.
What are the rules for dovetails?
Which is better English or French dovetail?
While both English and French dovetail construction are very sturdy and high quality, English dovetail construction is slightly sturdier with the trade-off of being more expensive and time-consuming to produce.
Is dovetail the strongest joint?
The advantages of the dovetail joint are that it is the strongest of all joints, has a large gluing area, is interlocking, resists being pulled apart, looks attractive, and would hold together even without glue.
What is the typical angle of a dovetail metal?
Angles used on dovetails On large industrial scale machines the angle is usually 45º. For smaller dovetails the usual angle is 60º. Any less than this, i.e. 60° on a small machine, complicates the design of the adjustment mechanism. The angle produced is set by the dovetail cutter used.
What ratio is a 14 degree dovetail?
Commonly accepted ratios are 1:8 for hardwoods and 1:6 for softer timber. This 14° marker equates to a ratio of 1:4. When used with thinner stock, the 14° angle results in a better looking joint.
What is the angle of a standard dovetail cutter?
O-ring dovetail cutters have an included angle of 48°. Another common included angle for general purpose dovetails is 90°.
What are the typical angles of dovetail markers?
Dovetail angles are expressed in two ways: as ratios and degrees. 1:8 roughly translates to 70 and 1:6 translates roughly as 90. These days, we often hear that 90 is recommended for softwoods, while 70 should be used for hardwoods.
What is the standard angle for a metal dovetail?
Angles used on dovetails On large industrial scale machines the angle is usually 45º. For smaller dovetails the usual angle is 60º. Any less than this, i.e. 60° on a small machine, complicates the design of the adjustment mechanism. The angle produced is set by the dovetail cutter used.
What is the formula for measuring dovetails?
To obtain dimension x for measuring male dovetails, add 1 to the cotangent of one-half the dovetail angle α, multiply by diameter D of the rods used, and add the product to dimension α.
Is a dovetail joint strong or weak?
Dovetail joints are known for their inherent strength and resistance to being pulled apart (tensile strength).
What is a 3 8 dovetail?
3/8″ dovetail rails, sometimes call tip off rails, consist of two thin parallel grooves and are used almost exclusively on rimfire rifles and air rifles. 3/8″ dovetail rails are a common, standardized style within the rimfire industry and are inexpensive to machine into the firearm’s frame.
Is dovetail joint permanent?
The strongest and most permanent right-angled joints made in wood are the ‘dove-tail’ joints, as illustrated below. The so-called tails and pins fit together to form a secure joint.
Why are dovetails so hard?
The dovetail joint is very strong because of the way the ‘tails’ and ‘pins’ are shaped. This makes it difficult to pull the joint apart and virtually impossible when glue is added.
Are dovetail joints still used?
They are still used today by many experienced custom furniture makers. Dovetail joints are not only used to make a strong joint for drawer construction, but cabinet makers often use them to join the tops, bottoms and sides of cabinet cases, as was done on antique furniture.
What is the best length for a dovetail saw?
Even if you’ll use your saw mostly for run of the mill drawer dovetails, the longer length will give much straighter cuts, and be much faster. It will also help you to see square. Go for around the 10″ (250mm) mark. Maybe a little longer if you work thicker stuff.
What is the most popular dovetail joint?
The through dovetail joint is the most popular dovetail joint because it is strong, attractive, and versatile. It is commonly used in furniture-making, cabinetry, and woodworking. The through dovetail joint is a traditional woodworking joint characterized by the interlocking triangular shape it creates.
When did they stop using dovetail?
By 1730, through dovetail joinery was abandoned in English furniture making in favor of the lapped construction. As furniture became more refined, furniture makers began to take pride in the construction of their drawers as well.
What is the weakest joint in carpentry?
A butt joint uses a simple technique whereby two pieces of material are joined together at their ends, without any special shaping or cutting. Although it is simple, the butt joint is also the weakest of the wood joinery types.
What is the highest quality joint?
Mortise and tenon joints have stood the test of time for their remarkable strength. This traditional joint involves a projecting piece of wood, called a tenon, securely fitting into a corresponding cavity, a mortise. It can be reinforced with glue or wedges for stability for a stronger hold.
What are the rules for dovetail?
What is the minimum thickness for a dovetail?
Structurally I have looked for pin strength in dovetails as the dovetailed aspect is always strong because it is always at least as wide and mostly wider than the pins. In my own work I aim for a minimum size of 1/4″ and mostly 3/8″.
