Standard dovetail joints have evenly spaced cut pins and tails, traditional dovetails have wide-cut pins and smaller tails. Standard cut pins and tails offer more strength in the drawer, traditional is not quite so strong but are often specified because of their traditional finish.
What is the standard dovetail ratio?
Dovetail angles are usually expressed as ratios — the most common being 1:6 and 1:8 (said “one in eight,” and also written as 6:1 or 8:1). As a general rule of thumb: Use 1:6 for softwoods. Use 1:8 for hardwoods.
What is the average size of a dovetail?
Dovetails come in several different types and sizes depending on manufacturer, but the most common are the 11 mm and 3⁄8 inch (9.5 mm). Some other less known, but currently commercially available dovetail mounts, are 12, 13, 13.5, 14, 14.5, 16, 16.5, 17 and 19 mm.
What is the most popular dovetail?
1) Through Dovetail Also known as the plain dovetail, this is the most common and basic type of dovetail joint. Through interlocking tails and pins, this joint showcases consistent angles, revealing the wood’s end grains on external surfaces.
What is the average size of a dovetail?
Dovetails come in several different types and sizes depending on manufacturer, but the most common are the 11 mm and 3⁄8 inch (9.5 mm). Some other less known, but currently commercially available dovetail mounts, are 12, 13, 13.5, 14, 14.5, 16, 16.5, 17 and 19 mm.
Is 11mm dovetail the same as 3 8?
The 3/8 Inch is measured across the bottom of the dovetail whereas the 11 mm is measured across the top of the dovetail. A 3/8 Inch dovetail is about 12.7 mm across the top. The measurements 3/8 and 11mm are not the same for this reason plus the angles are different.
What is the minimum thickness for a dovetail?
Structurally I have looked for pin strength in dovetails as the dovetailed aspect is always strong because it is always at least as wide and mostly wider than the pins. In my own work I aim for a minimum size of 1/4″ and mostly 3/8″.
How deep should a dovetail joint be?
Typically we use 1 ½” – 2” deep dovetails that are about 2” less deep than the joist, and 4” less deep than the girt – but that is just a starting point – the loads and reactions have to be calculated from there.
What is a 1 to 6 dovetail?
A 1:6 ratio – that’s one unit horizontal with six matching units drawn vertical – lays out as a 9.5 degree angle.
Which is better English or French dovetail?
While both English and French dovetail construction are very sturdy and high quality, English dovetail construction is slightly sturdier with the trade-off of being more expensive and time-consuming to produce.
What are the rules for dovetail joints?
The ‘pins’ are the bits of wood between the tails so there are two half-pins; one each side. The general rule is that they measure half the thickness of timber plus around a mm, so the two dots on the shoulder line are 7mm in from each edge.
What is an English dovetail joint?
A series of pins cut to extend from the end of one board interlock with a series of ‘tails’ cut into the end of another board. The pins and tails have a trapezoidal shape. Once glued, a wooden dovetail joint requires no mechanical fasteners.
Should you glue dovetail joints?
Michael Dresdner: The only areas that require glue on dovetails are the diagonal faces. All the diagonal faces are long grain, all the square faces are end grain, and all the flat faces abut end grain. Therefore, you need only apply glue to the diagonal faces on the tails or pins, or both.
What is the best tool for dovetail joints?
For making perfect fixed dovetail joints, many woodworkers turn to the Leigh Super 18-inch Dovetail Jig. Dovetails and half-blind dovetail joints can be made fast and effortlessly with this woodworking tool, and look like they’ve been professionally made.
What is stronger dovetail or finger joint?
Although the finger joint is not mechanically interlocking like a dovetail, the joint is amazingly strong. Today’s modern adhesives and the large glue surface make the finger joint equally as strong as the dovetail throughout the life of the adhesive.
What is the best angle for a dovetail joint?
Although softwoods are more compressible than hardwoods, you needn’t change the dovetail angle to add strength to the joint. Any angle between 7° and 15° will work, regardless of the wood. But stay within that range. If you go below 7°, you’ll start to lose the mechanical strength of the dovetail.
What are the proportions for a dovetail joint?
The only consistent advice I find is keep dovetail length about equal to board thickness. And keep dovetail ratios between 1:6 and 1:8.
What ratio is a 14 degree dovetail?
There is no hard and fast rule when it comes to dovetail angles. Commonly accepted ratios are 1:8 for hardwoods and 1:6 for softer timber. This 14° marker equates to a ratio of 1:4.
What is 1 to 6 ratio dovetail?
A 1:6 ratio – that’s one unit horizontal with six matching units drawn vertical – lays out as a 9.5 degree angle. A 1:8 ratio – one unit horizontal with eight matching units drawn vertical – is an angle of 7.1 degrees.
What does 1 6 dovetail mean?
They represent ratios that determine a dovetails angle. So in the case of 1:6 – for every unit you move up you also move 6 units over. These ratios are not usually mixed or changed on a single project.
What is the average size of a dovetail?
Dovetails come in several different types and sizes depending on manufacturer, but the most common are the 11 mm and 3⁄8 inch (9.5 mm). Some other less known, but currently commercially available dovetail mounts, are 12, 13, 13.5, 14, 14.5, 16, 16.5, 17 and 19 mm.
What rifles have 11mm dovetail?
Will 3 8 dovetail fit Picatinny rail?
3/8 Dovetail to Picatinny Adapter Rail -Short adaptor Rail attaches to 3/8 Dovetail rails and converts it to Picatinny Rail for mounting Red Dot optics with Weaver/Picatinny type rings and mounts.
What size is a standard Picatinny rail?
What is the weakness of dovetail joint?
The disadvantages of dovetail joints are that they can be fairly difficult to mark out and cut, and if they are made badly these joints lose the advantages listed above. Depending on the project, function, and design, there are a number of different types of dovetail joints to choose from.
Is dovetail joint permanent?
The strongest and most permanent right-angled joints made in wood are the ‘dove-tail’ joints, as illustrated below. The so-called tails and pins fit together to form a secure joint.
