As a rule of thumb the dovetail’s maximum width should occupy approximately 1/ 2 to 3/ 4 of the gasket’s width (leaving a 1/ 4 – 1/ 8 of gasket width on each side). For larger gasket widths, multiple dovetails can be made side-by- side, facing the same direction or inverted.
What is the standard angle for a dovetail?
Although softwoods are more compressible than hardwoods, you needn’t change the dovetail angle to add strength to the joint. Any angle between 7° and 15° will work, regardless of the wood. But stay within that range. If you go below 7°, you’ll start to lose the mechanical strength of the dovetail.
What size are standard dovetails?
Dovetail Dado Wood Joints have joint widths of 2/3 and joint depths of 1/2. Wood joints are typically used in wood members with widths between 1.5”-3.5” (3.8-8.9 cm) and depths between of . 75”-3.5” (1.9-8.9 cm).
How do you dimension a dovetail?
To obtain dimension x for measuring male dovetails, add 1 to the cotangent of one-half the dovetail angle α, multiply by diameter D of the rods used, and add the product to dimension α.
What size are dovetails?
Dovetails come in several different types and sizes depending on manufacturer, but the most common are the 11 mm and 3⁄8 inch (9.5 mm). Some other less known, but currently commercially available dovetail mounts, are 12, 13, 13.5, 14, 14.5, 16, 16.5, 17 and 19 mm.
What are the rules for dovetail joints?
The general rule is that they measure half the thickness of timber plus around 1 mm along the shoulder line. So these two awl dots are 7 mm in from each edge. These two dots, which mark the corners of the half pins, are now converted into a 1:8 slope at each side.
What is the difference between 11mm and 3 8 dovetail?
The 3/8 Inch is measured across the bottom of the dovetail whereas the 11 mm is measured across the top of the dovetail. A 3/8 Inch dovetail is about 12.7 mm across the top. The measurements 3/8 and 11mm are not the same for this reason plus the angles are different.
What is the most common dovetail ratio?
Dovetail angles are usually expressed as ratios — the most common being 1:6 and 1:8 (said “one in eight,” and also written as 6:1 or 8:1). As a general rule of thumb: Use 1:6 for softwoods. Use 1:8 for hardwoods.
What is the minimum thickness for a dovetail?
Structurally I have looked for pin strength in dovetails as the dovetailed aspect is always strong because it is always at least as wide and mostly wider than the pins. In my own work I aim for a minimum size of 1/4″ and mostly 3/8″.
What is the difference between English dovetail and French dovetail?
English dovetails are the most common. They have interlocking joints and allow the most amount of space – usually several more inches of room than you would get with French dovetails. This is because the dovetail groove cannot be put all the way at the edge of a drawer with French dovetails.
How do you find the angle of a dovetail slot?
You could take an over or between pins measurements if it’s the male or female part. Take 2 measurements using 2 different diameter pair of pins. Assuming the edges are fairly straight you should be able to deduce the dovetail angle.
How deep should dovetails be?
But keep in mind that if you machine the dovetail groove across the work piece you will be weakening it because you are removing some of its thickness. Try to keep the depth of the dovetail groove between 1/3 and 1/2 the thickness of the part.
What is a 6 to 1 dovetail?
A 1:6 ratio – that’s one unit horizontal with six matching units drawn vertical – lays out as a 9.5 degree angle.
Are all dovetail bits 14 degrees?
You’ll need a jig to make most dovetail joints, as well as a guide Bushing for your router. Check the instructions with your Dovetail jig to select a bit with the appropriate angle, which will usually be somewhere between 7 and 14 degrees.
What is the slope of a dovetail joint?
There are different types of dovetail joints. The angle of slope varies according to the wood used, purpose of joint and type of work. Typically the slope is 1:6 for softwoods, and a shallower 1:8 slope for hardwoods. Often a slope of 1:7 is used as a compromise.
What ratio is a 14 degree dovetail?
This 14° marker equates to a ratio of 1:4. When used with thinner stock, the 14° angle results in a better looking joint. This different angle also gives you a slightly stronger dovetail interlock on the thinner material.
What are the weaknesses of dovetail?
The disadvantages of dovetail joints are that they can be fairly difficult to mark out and cut, and if they are made badly these joints lose the advantages listed above. Depending on the project, function, and design, there are a number of different types of dovetail joints to choose from.
What is dovetail seniority?
DOVETAIL SENIORITY – The combination of two or more seniority lists (usually of different employers being merged) into a master seniority list, with each employee keeping the seniority previously acquired even though the employee may thereafter be employed by a new employer.
What is the most popular dovetail joint?
Single-lap Dovetail The single-lap (known to many folks as a half-blind dovetail) is the best known of the dovetails since it’s used to join the front to the sides of a drawer.
What is the best dovetail angle?
Lower (7° to 9°) angles are often advised for joining hardwoods, while higher angles (10° to 14°) are recommended for softwoods and even higher angles (14° to 18°) for half-blind dovetails.
Is dovetail the highest quality?
Dovetail joinery is a benchmark of high-quality construction because these fasteners are all potential weak points that can degrade or break-down over time.
What ratio is a 14 degree dovetail?
This 14° marker equates to a ratio of 1:4. When used with thinner stock, the 14° angle results in a better looking joint. This different angle also gives you a slightly stronger dovetail interlock on the thinner material.
Can you make dovetail joints with plywood?
A wide variety of methods can be used to make dovetail plywood drawer boxes. They are generally considered by the woodworking industry as time-consuming and difficult to make. The dovetails can be cut by hand with a dovetailing saw and chisel or you can use a dovetail jig and router.
What is stronger dovetail or finger joint?
The interlocking design of the dovetail creates a strong bond that can withstand a lot of stress. On the other hand, a box joint, also known as a finger joint, is strong in terms of sheer surface area and glue surface, making it suitable for joining the corners of a box or a drawer.
What is the weakest wood joint?
A butt joint uses a simple technique whereby two pieces of material are joined together at their ends, without any special shaping or cutting. Although it is simple, the butt joint is also the weakest of the wood joinery types.
