As a rule of thumb the dovetail’s maximum width should occupy approximately 1/ 2 to 3/ 4 of the gasket’s width (leaving a 1/ 4 – 1/ 8 of gasket width on each side). For larger gasket widths, multiple dovetails can be made side-by- side, facing the same direction or inverted.The dovetail groove construction is only recommended for O-rings with cross sections of.139 inch (3,53 mm) and larger. Surface Finish X groove top and bottom : for liquids X = 32 micro inches (0.8 μm Ra) For vacuum and gases X = 16 micro inches (0.4 μm Ra) Groove sides: X = 63 micro inches (1.6 μm Ra)
What are the proportions of a dovetail?
Dovetail angles are usually expressed as ratios — the most common being 1:6 and 1:8 (said “one in eight,” and also written as 6:1 or 8:1). As a general rule of thumb: Use 1:6 for softwoods. Use 1:8 for hardwoods.
What are the common dovetail sizes?
Dovetail Dado Wood Joints have joint widths of 2/3 and joint depths of 1/2. Wood joints are typically used in wood members with widths between 1.5”-3.5” (3.8-8.9 cm) and depths between of . 75”-3.5” (1.9-8.9 cm).
What is the standard for a dovetail?
11 mm and 3/8” dovetails are the two most common types of dovetails that you can find on rifles. The 11 mm dovetail represents a standard in Europe, while the 3/8” is a standard in the USA.
What is the tolerance for dovetails?
RE: DOVETAIL DIMENSIONING You apply a profile tolerance of 0.5mm and an angular tolerance of 0.1mm. Both tolerances specify the acceptable variation.
What is the minimum thickness for a dovetail?
In my own work I aim for a minimum size of 1/4″ and mostly 3/8″. Now that doesn’t mean I won’t go down to less or up too.
What is the best ratio for dovetails?
Anything from 1:6 to 1:9 looks good and works well. Too little rise leaves corners with short grain that easily breaks off, too much rise looks like a poorly made box joint. As long as it looks good, and assembles without breaking, its a good joint.
What is the most popular dovetail?
1) Through Dovetail Also known as the plain dovetail, this is the most common and basic type of dovetail joint. Through interlocking tails and pins, this joint showcases consistent angles, revealing the wood’s end grains on external surfaces.
Are 3 8 and 11mm dovetail the same?
The 3/8 Inch is measured across the bottom of the dovetail whereas the 11 mm is measured across the top of the dovetail. A 3/8 Inch dovetail is about 12.7 mm across the top. The measurements 3/8 and 11mm are not the same for this reason plus the angles are different.
What is a 1 8 dovetail ratio?
A 1:8 ratio – one unit horizontal with eight matching units drawn vertical – is an angle of 7.1 degrees.
What is the ratio for 14 degree dovetail?
This 14° marker equates to a ratio of 1:4. When used with thinner stock, the 14° angle results in a better looking joint. This different angle also gives you a slightly stronger dovetail interlock on the thinner material.
How do you space out dovetails?
There should be roughly one dovetail each 25mm or so across the width. There’s no hard and fast rule so it’s up to the woodworker to use his or her judgement to decide how many are needed.
How deep should a dovetail joint be?
Typically we use 1 ½” – 2” deep dovetails that are about 2” less deep than the joist, and 4” less deep than the girt – but that is just a starting point – the loads and reactions have to be calculated from there.
How deep should dovetails be?
Try to keep the depth of the dovetail groove between 1/3 and 1/2 the thickness of the part. For example, if the gable of a chest of drawers is 3/4″ thick, machine the dovetail groove between 1/4″ and 3/8″ deep. Any deeper and you will weaken the gable too much.
What are the weaknesses of dovetail?
The disadvantages of dovetail joints are that they can be fairly difficult to mark out and cut, and if they are made badly these joints lose the advantages listed above. Depending on the project, function, and design, there are a number of different types of dovetail joints to choose from.
What ratio is a 14 degree dovetail?
This 14° marker equates to a ratio of 1:4. When used with thinner stock, the 14° angle results in a better looking joint. This different angle also gives you a slightly stronger dovetail interlock on the thinner material.
What is a 1 6 ratio for dovetails?
A 1:6 ratio – that’s one unit horizontal with six matching units drawn vertical – lays out as a 9.5 degree angle. A 1:8 ratio – one unit horizontal with eight matching units drawn vertical – is an angle of 7.1 degrees.
What is the formula for measuring dovetails?
To obtain dimension x for measuring male dovetails, add 1 to the cotangent of one-half the dovetail angle α, multiply by diameter D of the rods used, and add the product to dimension α.
Are 3 8 and 11mm dovetail the same?
The 3/8 Inch is measured across the bottom of the dovetail whereas the 11 mm is measured across the top of the dovetail. A 3/8 Inch dovetail is about 12.7 mm across the top. The measurements 3/8 and 11mm are not the same for this reason plus the angles are different.
What are the important information of dovetail joints?
Dovetail joints are known for their inherent strength and resistance to being pulled apart (tensile strength). A dovetail joint has a series of pins and tails in a trapezoidal shape and once glued a dovetail joint has no need for mechanical fasteners.
Should dovetail joints be glued?
Michael Dresdner: The only areas that require glue on dovetails are the diagonal faces. All the diagonal faces are long grain, all the square faces are end grain, and all the flat faces abut end grain. Therefore, you need only apply glue to the diagonal faces on the tails or pins, or both.
What is the best dovetail angle?
Lower (7° to 9°) angles are often advised for joining hardwoods, while higher angles (10° to 14°) are recommended for softwoods and even higher angles (14° to 18°) for half-blind dovetails.
What is the easiest wood for dovetails?
Soft maple, or red maple, can be a great wood to practice dovetails on. It has very tight and closed grain making it a joy to saw, chisel, and pare.
What makes a dovetail joint so strong?
Methods. The dovetail joint is very strong because of the way the ‘tails’ and ‘pins’ are shaped. This makes it difficult to pull the joint apart and virtually impossible when glue is added.
What is the difference between English dovetail and French dovetail?
English dovetails are the most common. They have interlocking joints and allow the most amount of space – usually several more inches of room than you would get with French dovetails. This is because the dovetail groove cannot be put all the way at the edge of a drawer with French dovetails.
What is the best chisel for dovetails?
The triangular cross-section of these chisels make them ideal for paring and chopping away the waste on dovetail joinery. Suitable for other joinery tasks, these affordable chisels are a nice complement to standard bench chisels for creating and fine-tuning joinery.
