Dovetail angles are usually expressed as ratios — the most common being 1:6 and 1:8 (said “one in eight,” and also written as 6:1 or 8:1). As a general rule of thumb: Use 1:6 for softwoods. Use 1:8 for hardwoods.
What ratio for dovetail hardwood?
Anything from 1:6 to 1:9 looks good and works well. Too little rise leaves corners with short grain that easily breaks off, too much rise looks like a poorly made box joint. As long as it looks good, and assembles without breaking, its a good joint.
What is the ratio for 14 degree dovetail?
There is no hard and fast rule when it comes to dovetail angles. Commonly accepted ratios are 1:8 for hardwoods and 1:6 for softer timber. This 14° marker equates to a ratio of 1:4.
What is a 6 to 1 dovetail?
A 1:6 ratio – that’s one unit horizontal with six matching units drawn vertical – lays out as a 9.5 degree angle.
What is the formula for measuring dovetails?
To obtain dimension x for measuring male dovetails, add 1 to the cotangent of one-half the dovetail angle α, multiply by diameter D of the rods used, and add the product to dimension α.
What ratio for dovetail hardwood?
Anything from 1:6 to 1:9 looks good and works well. Too little rise leaves corners with short grain that easily breaks off, too much rise looks like a poorly made box joint. As long as it looks good, and assembles without breaking, its a good joint.
What is a 6 to 1 dovetail?
A 1:6 ratio – that’s one unit horizontal with six matching units drawn vertical – lays out as a 9.5 degree angle.
What dovetail ratio is best?
Dovetail angles are usually expressed as ratios — the most common being 1:6 and 1:8 (said “one in eight,” and also written as 6:1 or 8:1). As a general rule of thumb: Use 1:6 for softwoods. Use 1:8 for hardwoods.
What is the most common dovetail angle?
Percy Blandford, who has been writing about woodworking for a long time, writes in “The Woodworker’s Bible” that any angle between 7.5° and 10° is acceptable. The ideal, he says, is 8.5° for softwoods and 7.5° when joining hardwoods.
Is 11mm dovetail the same as 3 8?
However, that is not the only difference between the two dovetails. They also have different groove angles as shown below. The 11 mm dovetail has a 60-degree angle, while the 3/8” dovetail has a 45-degree angle.
What is a standard dovetail?
A series of pins cut to extend from the end of one board interlock with a series of ‘tails’ cut into the end of another board. The pins and tails have a trapezoidal shape. Once glued, a wooden dovetail joint requires no mechanical fasteners.
What is the standard size of a dovetail?
Dovetail Dado Wood Joints have joint widths of 2/3 and joint depths of 1/2. Wood joints are typically used in wood members with widths between 1.5”-3.5” (3.8-8.9 cm) and depths between of . 75”-3.5” (1.9-8.9 cm).
What are the rules for dovetail design?
As a rule of thumb the dovetail’s maximum width should occupy approximately 1/ 2 to 3/ 4 of the gasket’s width (leaving a 1/ 4 – 1/ 8 of gasket width on each side). For larger gasket widths, multiple dovetails can be made side-by- side, facing the same direction or inverted.
How do you choose a dovetail angle?
Although softwoods are more compressible than hardwoods, you needn’t change the dovetail angle to add strength to the joint. Any angle between 7° and 15° will work, regardless of the wood. But stay within that range. If you go below 7°, you’ll start to lose the mechanical strength of the dovetail.
What is the best dovetail ratio?
Over time you will probably notice an affinity to a certain ratio; personally, I like 1:7 best. Next time you cut a set of dovetails, don’t overthink things. Layout what you think looks good and go to it.
Is 11mm dovetail the same as 3 8?
However, that is not the only difference between the two dovetails. They also have different groove angles as shown below. The 11 mm dovetail has a 60-degree angle, while the 3/8” dovetail has a 45-degree angle.
What is the best dovetail angle for hardwood?
My go-to angle for through dovetails in most hardwoods is 7:1 (8.1°), such as for a carcase or box in cherry, maple, or walnut with stock thickness of 9/16″-13/16″. It has enough angle to form a strong mechanical lock but not too much to produce fragile tail corners or overly fussy fitting.
What is the difference between 11mm and 3 8 dovetail?
The 3/8 Inch is measured across the bottom of the dovetail whereas the 11 mm is measured across the top of the dovetail. A 3/8 Inch dovetail is about 12.7 mm across the top. The measurements 3/8 and 11mm are not the same for this reason plus the angles are different.
What ratio for dovetail hardwood?
Anything from 1:6 to 1:9 looks good and works well. Too little rise leaves corners with short grain that easily breaks off, too much rise looks like a poorly made box joint. As long as it looks good, and assembles without breaking, its a good joint.
What is a 6 to 1 dovetail?
A 1:6 ratio – that’s one unit horizontal with six matching units drawn vertical – lays out as a 9.5 degree angle.
What is the most popular dovetail joint?
Single-lap Dovetail The single-lap (known to many folks as a half-blind dovetail) is the best known of the dovetails since it’s used to join the front to the sides of a drawer.
What is stronger dovetail or finger joint?
The interlocking design of the dovetail creates a strong bond that can withstand a lot of stress. On the other hand, a box joint, also known as a finger joint, is strong in terms of sheer surface area and glue surface, making it suitable for joining the corners of a box or a drawer.
Which is better English or French dovetail?
While both English and French dovetail construction are very sturdy and high quality, English dovetail construction is slightly sturdier with the trade-off of being more expensive and time-consuming to produce.
What is the minimum thickness for a dovetail?
Structurally I have looked for pin strength in dovetails as the dovetailed aspect is always strong because it is always at least as wide and mostly wider than the pins. In my own work I aim for a minimum size of 1/4″ and mostly 3/8″.
What are the weaknesses of dovetail?
The disadvantages of dovetail joints are that they can be fairly difficult to mark out and cut, and if they are made badly these joints lose the advantages listed above. Depending on the project, function, and design, there are a number of different types of dovetail joints to choose from.
How many pins are in a dovetail joint?
There is usually a three pin setup but more or less pins can be used depending on how much strength and aesthetics you want.
