Percy Blandford, who has been writing about woodworking for a long time, writes in “The Woodworker’s Bible” that any angle between 7.5° and 10° is acceptable. The ideal, he says, is 8.5° for softwoods and 7.5° when joining hardwoods.
What is the strongest angle for a dovetail?
Any angle between 7° and 15° will work, regardless of the wood. But stay within that range. If you go below 7°, you’ll start to lose the mechanical strength of the dovetail. Go above 15°, and you’ll leave too much short grain at the tips of the tails, which weakens the joinery.
What angle do you cut dovetail joint?
The angle of a dovetail joint should be between 7 and 15 degrees: too broad and the joint won’t be strong enough, too skinny, and the pin can snap. So the angle of the dovetail mainly depends on the use and wear the joint will get. 5. They are called ‘dovetails’ because they are shaped like the tail feathers of a dove!
What is the ratio of a dovetail to an angle?
A 1:6 ratio – that’s one unit horizontal with six matching units drawn vertical – lays out as a 9.5 degree angle. A 1:8 ratio – one unit horizontal with eight matching units drawn vertical – is an angle of 7.1 degrees.
What is the strongest angle for a dovetail?
Any angle between 7° and 15° will work, regardless of the wood. But stay within that range. If you go below 7°, you’ll start to lose the mechanical strength of the dovetail. Go above 15°, and you’ll leave too much short grain at the tips of the tails, which weakens the joinery.
What is the weakness of dovetail joint?
The disadvantages of dovetail joints are that they can be fairly difficult to mark out and cut, and if they are made badly these joints lose the advantages listed above. Depending on the project, function, and design, there are a number of different types of dovetail joints to choose from.
Is 11mm dovetail the same as 3 8?
However, that is not the only difference between the two dovetails. They also have different groove angles as shown below. The 11 mm dovetail has a 60-degree angle, while the 3/8” dovetail has a 45-degree angle.
What are the rules for dovetail joints?
The pins and tails only fit together from one direction. The single dovetail joint can either be a complete pin or a complete tale (Figure I). The multiple dovetail usually ends with a half pin on the corner; the half tail is usually avoided (Figure II). The tail board is a mirror of itself.
Which part of a dovetail do you cut first?
Knowing both ways means that repairs can be made when something goes wrong. Add into the equation that it is extremely difficult to cut half-lap dovetails accurately using the pins-first method, it makes sense to cut tails first as a matter of course.
What is the best dovetail ratio?
As regards the ratio to use on various woods, dont get your knickers in a knot. Anything from 1:6 to 1:9 looks good and works well. Too little rise leaves corners with short grain that easily breaks off, too much rise looks like a poorly made box joint.
How do you find the angle of a dovetail slot?
You could take an over or between pins measurements if it’s the male or female part. Take 2 measurements using 2 different diameter pair of pins. Assuming the edges are fairly straight you should be able to deduce the dovetail angle.
What ratio is a 14 degree dovetail?
There is no hard and fast rule when it comes to dovetail angles. Commonly accepted ratios are 1:8 for hardwoods and 1:6 for softer timber. This 14° marker equates to a ratio of 1:4.
What is the strongest support angle?
45 degrees is the strongest brace angle for a right-angle triangle, but the absolutely strongest is an equilateral triangle with three 60 degree angles.
What makes a dovetail joint strong?
The dovetail joint is very strong because of the way the ‘tails’ and ‘pins’ are shaped. This makes it difficult to pull the joint apart and virtually impossible when glue is added.
Are all dovetail bits 14 degrees?
You’ll need a jig to make most dovetail joints, as well as a guide Bushing for your router. Check the instructions with your Dovetail jig to select a bit with the appropriate angle, which will usually be somewhere between 7 and 14 degrees.
What is the strongest angle for a dovetail?
Any angle between 7° and 15° will work, regardless of the wood. But stay within that range. If you go below 7°, you’ll start to lose the mechanical strength of the dovetail. Go above 15°, and you’ll leave too much short grain at the tips of the tails, which weakens the joinery.
Should you glue dovetail joints?
Michael Dresdner: The only areas that require glue on dovetails are the diagonal faces. All the diagonal faces are long grain, all the square faces are end grain, and all the flat faces abut end grain. Therefore, you need only apply glue to the diagonal faces on the tails or pins, or both.
What is the weakest joint in carpentry?
A butt joint uses a simple technique whereby two pieces of material are joined together at their ends, without any special shaping or cutting. Although it is simple, the butt joint is also the weakest of the wood joinery types.
What is the most popular dovetail joint?
Single-lap Dovetail The single-lap (known to many folks as a half-blind dovetail) is the best known of the dovetails since it’s used to join the front to the sides of a drawer.
How big should a dovetail joint be?
For drawers, boxes or trays 2″ or less I generally like a single dovetail. For 3″ to 3 1/2″ and less two dovetails, for 4″ three dovetails, for 5″ to 6″ four dovetails and for 6″ four or possibly five.
Is dovetail the strongest joint?
The interlocking design of the dovetail joint makes it significantly stronger than many other types of joints, such as butt joints or mitre joints. This strength is due to the large amount of surface area for glue to adhere to, as well as the mechanical interlocking of the fingers of the joint.
What is a standard dovetail?
A series of pins cut to extend from the end of one board interlock with a series of ‘tails’ cut into the end of another board. The pins and tails have a trapezoidal shape. Once glued, a wooden dovetail joint requires no mechanical fasteners.
Is a finger joint stronger than a dovetail joint?
For box joint, some people put a lot more fingers than it is possible to do with Dovetail. In this case, the gluing surface is larger, and the joint is likely stronger. Also, some find a way to hide a finish nail in the joint. Dovetail has the advantage of a mechanical lock independent of the glue.
How deep should dovetails be?
But keep in mind that if you machine the dovetail groove across the work piece you will be weakening it because you are removing some of its thickness. Try to keep the depth of the dovetail groove between 1/3 and 1/2 the thickness of the part.
Is dovetail joint permanent?
The strongest and most permanent right-angled joints made in wood are the ‘dove-tail’ joints, as illustrated below. The so-called tails and pins fit together to form a secure joint.
Which is better English or French dovetail?
While both English and French dovetail construction are very sturdy and high quality, English dovetail construction is slightly sturdier with the trade-off of being more expensive and time-consuming to produce.
