For those of you unfamiliar with them, the angle at which dovetails are cut is usually referred to by ratio, for example, 1:7 or 1:6. To draw the angle, you layout a horizontal line with a vertical line intersecting it at 90 degrees.Dovetail angles are usually expressed as ratios — the most common being 1:6 and 1:8 (said “one in eight,” and also written as 6:1 or 8:1). As a general rule of thumb: Use 1:6 for softwoods. Use 1:8 for hardwoods.
What angle should a dovetail joint be?
The angle of a dovetail joint should be between 7 and 15 degrees: too broad and the joint won’t be strong enough, too skinny, and the pin can snap. So the angle of the dovetail mainly depends on the use and wear the joint will get. 5. They are called ‘dovetails’ because they are shaped like the tail feathers of a dove!
What ratio is a 14 degree dovetail?
There is no hard and fast rule when it comes to dovetail angles. Commonly accepted ratios are 1:8 for hardwoods and 1:6 for softer timber. This 14° marker equates to a ratio of 1:4.
What angle is 6 to 1 dovetail?
A 1:6 ratio – that’s one unit horizontal with six matching units drawn vertical – lays out as a 9.5 degree angle. A 1:8 ratio – one unit horizontal with eight matching units drawn vertical – is an angle of 7.1 degrees.
What is the ratio of pin to tail for dovetail joints?
The line between that end point and starting point will be the angle of your tail and pin sides. 6:1 (9.5°) and 8:1 (7.1°) dovetail ratios are the most common (though you’ll often see 4:1 and 10:1 as well).
What angle is 6 to 1 dovetail?
A 1:6 ratio – that’s one unit horizontal with six matching units drawn vertical – lays out as a 9.5 degree angle. A 1:8 ratio – one unit horizontal with eight matching units drawn vertical – is an angle of 7.1 degrees.
What are the measurements for a dovetail joint?
Dovetail Dado Wood Joints have joint widths of 2/3 and joint depths of 1/2. Wood joints are typically used in wood members with widths between 1.5”-3.5” (3.8-8.9 cm) and depths between of . 75”-3.5” (1.9-8.9 cm).
How do you calculate dovetail joints?
What is the best dovetail ratio?
Dovetail angles are usually expressed as ratios — the most common being 1:6 and 1:8 (said “one in eight,” and also written as 6:1 or 8:1). As a general rule of thumb: Use 1:6 for softwoods. Use 1:8 for hardwoods.
What is the most common dovetail angle?
Percy Blandford, who has been writing about woodworking for a long time, writes in “The Woodworker’s Bible” that any angle between 7.5° and 10° is acceptable. The ideal, he says, is 8.5° for softwoods and 7.5° when joining hardwoods.
What is the strongest angle for a dovetail?
Any angle between 7° and 15° will work, regardless of the wood. But stay within that range. If you go below 7°, you’ll start to lose the mechanical strength of the dovetail. Go above 15°, and you’ll leave too much short grain at the tips of the tails, which weakens the joinery.
What is the angle of a 11mm dovetail?
The 11 mm dovetail has a 60-degree angle, while the 3/8” dovetail has a 45-degree angle.
What is the degree of a 1 in 8 dovetail?
It would be extremely difficult to be able to pick these differences up in your dovetails on a piece of furniture by eye. So in closing your 1:4 Saddle-Tail is for all practical purposes 14 degrees, the 1:6 is close to 10 degrees and the 1:8 is about 7 degrees.
What is the difference between 11mm and 3 8 dovetail?
The 3/8 Inch is measured across the bottom of the dovetail whereas the 11 mm is measured across the top of the dovetail. A 3/8 Inch dovetail is about 12.7 mm across the top. The measurements 3/8 and 11mm are not the same for this reason plus the angles are different.
What is stronger dovetail or finger joint?
Although the finger joint is not mechanically interlocking like a dovetail, the joint is amazingly strong. Today’s modern adhesives and the large glue surface make the finger joint equally as strong as the dovetail throughout the life of the adhesive.
What makes a dovetail joint so strong?
The dovetail joint is very strong because of the way the ‘tails’ and ‘pins’ are shaped. This makes it difficult to pull the joint apart and virtually impossible when glue is added.
What is the weakness of dovetail joint?
The disadvantages of dovetail joints are that they can be fairly difficult to mark out and cut, and if they are made badly these joints lose the advantages listed above. Depending on the project, function, and design, there are a number of different types of dovetail joints to choose from.
Should dovetail joints be glued?
Michael Dresdner: The only areas that require glue on dovetails are the diagonal faces. All the diagonal faces are long grain, all the square faces are end grain, and all the flat faces abut end grain. Therefore, you need only apply glue to the diagonal faces on the tails or pins, or both.
What is the most popular dovetail joint?
Single-lap Dovetail The single-lap (known to many folks as a half-blind dovetail) is the best known of the dovetails since it’s used to join the front to the sides of a drawer.
What angle is 6 to 1 dovetail?
A 1:6 ratio – that’s one unit horizontal with six matching units drawn vertical – lays out as a 9.5 degree angle. A 1:8 ratio – one unit horizontal with eight matching units drawn vertical – is an angle of 7.1 degrees.
What is the formula for measuring dovetails?
To obtain dimension x for measuring male dovetails, add 1 to the cotangent of one-half the dovetail angle α, multiply by diameter D of the rods used, and add the product to dimension α.
What are the rules for dovetail design?
As a rule of thumb the dovetail’s maximum width should occupy approximately 1/ 2 to 3/ 4 of the gasket’s width (leaving a 1/ 4 – 1/ 8 of gasket width on each side). For larger gasket widths, multiple dovetails can be made side-by- side, facing the same direction or inverted.
Which is better English or French dovetail?
While both English and French dovetail construction are very sturdy and high quality, English dovetail construction is slightly sturdier with the trade-off of being more expensive and time-consuming to produce.
What is the minimum thickness for a dovetail?
Structurally I have looked for pin strength in dovetails as the dovetailed aspect is always strong because it is always at least as wide and mostly wider than the pins. In my own work I aim for a minimum size of 1/4″ and mostly 3/8″.
What is the most popular dovetail joint?
Single-lap Dovetail The single-lap (known to many folks as a half-blind dovetail) is the best known of the dovetails since it’s used to join the front to the sides of a drawer.
Are dovetail joints worth it?
Making sure that you pick a drawer joint that can withstand this type of wear and tear is crucial to the longevity of your kitchen cabinets. Dovetail joints are considered one of the strongest joints used in kitchen cabinetry construction and are the best solution for a kitchen cabinet drawer box.
