This joint type has two parts, called pins and tails. You can tell the difference between these two pieces because the tails are flared triangular shapes, while the pins are thinner. The tails, which look like those of a dove, are what give the dovetail joint its name.
What do dovetail joints look like?
There are two parts to a dovetail joint, pins and tails. The tails look like the tail of a dove (hence the name), and the pins are on the opposite board and fit in between the tails to create a joint that is impossible to pull apart in at least one direction.
What is an example of a dovetail?
A dovetail is a joint in woodworking where two sides are fitted together with interlocking pieces. You can also use the word dovetail to show how other things fit well together — like how your picnic plans nicely dovetail with the sunny forecast.
What do dovetail joints look like?
There are two parts to a dovetail joint, pins and tails. The tails look like the tail of a dove (hence the name), and the pins are on the opposite board and fit in between the tails to create a joint that is impossible to pull apart in at least one direction.
When did they stop using dovetail joints?
By 1730, through dovetail joinery was abandoned in English furniture making in favor of the lapped construction. As furniture became more refined, furniture makers began to take pride in the construction of their drawers as well.
What are the rules for dovetail joints?
The pins and tails only fit together from one direction. The single dovetail joint can either be a complete pin or a complete tale (Figure I). The multiple dovetail usually ends with a half pin on the corner; the half tail is usually avoided (Figure II). The tail board is a mirror of itself.
What is an English dovetail joint?
A dovetail joint is a locking joint. The English dovetail construction tends to allow for the largest possible drawer storage capacity. French dovetail construction is used for more elaborate features such a curved, bowed design.
Should you glue dovetail joints?
Michael Dresdner: The only areas that require glue on dovetails are the diagonal faces. All the diagonal faces are long grain, all the square faces are end grain, and all the flat faces abut end grain. Therefore, you need only apply glue to the diagonal faces on the tails or pins, or both.
What is the difference between a dovetail and mortise joint?
First of all the mortis and tenon are straight cut joints as opposed to the dovetail which is angled (like a dove tail). The m&t uses a bolt to hold the joint while the glue dries. The dove tail uses the pressure of the wood against wood and can actually stay seated without any glue in place.
What is the most popular dovetail joint?
The through dovetail joint is the most popular dovetail joint because it is strong, attractive, and versatile. It is commonly used in furniture-making, cabinetry, and woodworking. The through dovetail joint is a traditional woodworking joint characterized by the interlocking triangular shape it creates.
Are dovetail joints still used?
They are still used today by many experienced custom furniture makers. Dovetail joints are not only used to make a strong joint for drawer construction, but cabinet makers often use them to join the tops, bottoms and sides of cabinet cases, as was done on antique furniture.
Why is it called a dovetail joint?
Dovetail joints are made up of two parts called pins and tails. When a master craftsman wants to marry two boards together, they cut a series of pins on one board and matching tails on the other. They are trapezoidal in shape, resembling the tail feathers of a dove (hence the name dovetail).
What is the difference between a dovetail and mortise joint?
First of all the mortis and tenon are straight cut joints as opposed to the dovetail which is angled (like a dove tail). The m&t uses a bolt to hold the joint while the glue dries. The dove tail uses the pressure of the wood against wood and can actually stay seated without any glue in place.
Is dovetail joint permanent?
The strongest and most permanent right-angled joints made in wood are the ‘dove-tail’ joints, as illustrated below. The so-called tails and pins fit together to form a secure joint.
Are dovetail joints still used?
They are still used today by many experienced custom furniture makers. Dovetail joints are not only used to make a strong joint for drawer construction, but cabinet makers often use them to join the tops, bottoms and sides of cabinet cases, as was done on antique furniture.
What is a dovetail joint commonly used for?
Applications of a Dovetail Joint? Dovetail joints are most commonly used woodworking. Carpenters use dovetail joints to create cabinets, furniture, drawers, log buildings, carcass construction, timber framing. Dovetail joints are known for their strength and durability.
What do dovetail joints look like?
There are two parts to a dovetail joint, pins and tails. The tails look like the tail of a dove (hence the name), and the pins are on the opposite board and fit in between the tails to create a joint that is impossible to pull apart in at least one direction.
What is an alternative to a dovetail joint?
Finger joints are an effective and striking alternative to traditional dovetail joinery.
Which is better English or French dovetail?
While both English and French dovetail construction are very sturdy and high quality, English dovetail construction is slightly sturdier with the trade-off of being more expensive and time-consuming to produce.
What angle is a dovetail joint?
The angle of a dovetail joint should be between 7 and 15 degrees: too broad and the joint won’t be strong enough, too skinny, and the pin can snap. So the angle of the dovetail mainly depends on the use and wear the joint will get. 5. They are called ‘dovetails’ because they are shaped like the tail feathers of a dove!
How deep should a dovetail joint be?
Typically we use 1 ½” – 2” deep dovetails that are about 2” less deep than the joist, and 4” less deep than the girt – but that is just a starting point – the loads and reactions have to be calculated from there.
Can you make a dovetail joint by hand?
Of the four types of dovetail joints (through dovetail, half blind dovetail, secret mitered dovetail, and the sliding dovetail), the through dovetail is the most basic method, and a perfect one for hand cutting. Contrary to what seems to be popular belief on the internet, they are not really all that hard.
How difficult is a dovetail joint?
Hand-cutting a dovetail joint is kind of a woodworking high-wire act; one slip of the saw or chisel and the joint either won’t fit together or will look sloppy. It takes a lot of time to master the ability to cut dovetails quickly and well (by hand or machine), without a lot of fussing around.
Are dovetail joints antique?
Most quality pieces of antique furniture will have a dovetail joint in the drawer construction as it was a very early form of construction, but was so successful, it was used for many 100’s of years. The Dovetail joint, got its name because of its similarity to the shape of a birds tail.
Are dovetail joints easy to make?
Dovetails are Relatively Easy Making tails for dovetail joints is relatively easy. The most important part when you’re learning of how to make dovetail joints is to ensure that you make good and accurate pins and sockets so you will have accurate fitting dovetail joints using a dovetail jig.
Can you make dovetail joints with plywood?
A wide variety of methods can be used to make dovetail plywood drawer boxes. They are generally considered by the woodworking industry as time-consuming and difficult to make. The dovetails can be cut by hand with a dovetailing saw and chisel or you can use a dovetail jig and router.
