After setting up the jig, I installed the recommended dovetail bit and carefully set it to 3/8-inch depth. My jig specifies this depth is measured from the template, not the router base. I set my depth with a combination square so I laid the template on the router base and measured from that surface.
How deep should a dovetail be?
With a 3⁄4″-diameter flush-trimming bit in your router, plow out the dado to 3⁄16″ deep. Next, take your router with a tem- plate guide and dovetail bit, set it to 9⁄16″ deep (without moving the straightedge) and make the cut into the case side. The cut should be a bit longer than the width of your front divider.
What are the rules for dovetail joints?
The space between half pins is divided between pins and tails. Fine work the pins 4mm > 6mm, larger work 7mm > 12mm. To have a desirable appearance the pins smaller than the tails. Your tails should be around 18mm > 35mm for fine work like drawers and 35mm > 55mm on larger work like a chest.
What is the minimum thickness for a dovetail joint?
you; we recommend at least 8mm shanks, but 1⁄2″ would be even better, with of course the appropriate guide- bush. If you have to use 1⁄4″ shanks in hardwood, use a second router to rough out the slot centre with a straight cutter. We recommend 5⁄8″[15,9mm] as the min- imum size guidebush for sliding dovetails.
How big should a dovetail joint be?
For drawers, boxes or trays 2″ or less I generally like a single dovetail. For 3″ to 3 1/2″ and less two dovetails, for 4″ three dovetails, for 5″ to 6″ four dovetails and for 6″ four or possibly five.
How big should a dovetail joint be?
For drawers, boxes or trays 2″ or less I generally like a single dovetail. For 3″ to 3 1/2″ and less two dovetails, for 4″ three dovetails, for 5″ to 6″ four dovetails and for 6″ four or possibly five.
What are the disadvantages of a dovetail joint?
The disadvantages of dovetail joints are that they can be fairly difficult to mark out and cut, and if they are made badly these joints lose the advantages listed above. Depending on the project, function, and design, there are a number of different types of dovetail joints to choose from.
What is 11mm dovetail?
The standard 22 tip-off dovetail in the US is 3/8″ at the bottom and up to 1/2″ at the top. The European 11mm dovetail is typically 11mm at the top and perhaps 8mm at the bottom. The 11mm dovetail typically has a 60 degree angle from the bottom inside corner to the top where the 3/8″ is typically 45 degrees.
Should dovetail joints be glued?
Michael Dresdner: The only areas that require glue on dovetails are the diagonal faces. All the diagonal faces are long grain, all the square faces are end grain, and all the flat faces abut end grain. Therefore, you need only apply glue to the diagonal faces on the tails or pins, or both.
Are dovetail joints worth it?
This adds extreme strength to the drawer box joints. It is almost impossible for the joints to break because of the dovetail cuts as well as it being made from solid wood. In addition to this, most companies will also add the full extension, undermount, soft closing drawer guides.
Are dovetail joints permanent?
The strongest and most permanent right-angled joints made in wood are the ‘dove-tail’ joints, as illustrated below. The so-called tails and pins fit together to form a secure joint.
What is the most popular dovetail joint?
Single-lap Dovetail The single-lap (known to many folks as a half-blind dovetail) is the best known of the dovetails since it’s used to join the front to the sides of a drawer.
Is a finger joint stronger than a dovetail joint?
For box joint, some people put a lot more fingers than it is possible to do with Dovetail. In this case, the gluing surface is larger, and the joint is likely stronger. Also, some find a way to hide a finish nail in the joint. Dovetail has the advantage of a mechanical lock independent of the glue.
What makes a dovetail joint so strong?
The dovetail joint is very strong because of the way the ‘tails’ and ‘pins’ are shaped. This makes it difficult to pull the joint apart and virtually impossible when glue is added.
How do you calculate dovetail joints?
What is a standard dovetail?
Standard dovetail joints have evenly spaced cut pins and tails, traditional dovetails have wide-cut pins and smaller tails. Standard cut pins and tails offer more strength in the drawer, traditional is not quite so strong but are often specified because of their traditional finish.
What is the average size of a dovetail?
Dovetails come in several different types and sizes depending on manufacturer, but the most common are the 11 mm and 3⁄8 inch (9.5 mm). Some other less known, but currently commercially available dovetail mounts, are 12, 13, 13.5, 14, 14.5, 16, 16.5, 17 and 19 mm.
What is a standard dovetail?
Standard dovetail joints have evenly spaced cut pins and tails, traditional dovetails have wide-cut pins and smaller tails. Standard cut pins and tails offer more strength in the drawer, traditional is not quite so strong but are often specified because of their traditional finish.
What is the best length for a dovetail saw?
Even if you’ll use your saw mostly for run of the mill drawer dovetails, the longer length will give much straighter cuts, and be much faster. It will also help you to see square. Go for around the 10″ (250mm) mark. Maybe a little longer if you work thicker stuff.
What are the standard dimensions of a rifle dovetail?
But there are some mounts made specifically to fit both dovetails. This is possible due to these mounts having something called a “reversible clamp” which can be rotated to hold onto different dovetail angles and widths. 11 mm and 3/8” dovetails are the two most common types of dovetails that you can find on rifles.
What is the weakest wood joint?
A butt joint uses a simple technique whereby two pieces of material are joined together at their ends, without any special shaping or cutting. Although it is simple, the butt joint is also the weakest of the wood joinery types.
Can you make dovetail joints with plywood?
A wide variety of methods can be used to make dovetail plywood drawer boxes. They are generally considered by the woodworking industry as time-consuming and difficult to make. The dovetails can be cut by hand with a dovetailing saw and chisel or you can use a dovetail jig and router.
When would you use a dovetail joint?
Dovetail joints are a strong and attractive way to connect two pieces of wood at right angles. They work by using trapezoidal-shaped pins on one piece that interlock with corresponding tails on the other piece. This creates a strong mechanical bond that resists pulling apart.
What is the average size of a dovetail?
Dovetails come in several different types and sizes depending on manufacturer, but the most common are the 11 mm and 3⁄8 inch (9.5 mm). Some other less known, but currently commercially available dovetail mounts, are 12, 13, 13.5, 14, 14.5, 16, 16.5, 17 and 19 mm.
Is a dovetail joint strong or weak?
Dovetails are considerably weaker than mortise and tenon joints, be cautious as to where you employ them. I attached a table with sliding dovetails recently, they were 36” long joints.
What is the best dovetail angle?
Lower (7° to 9°) angles are often advised for joining hardwoods, while higher angles (10° to 14°) are recommended for softwoods and even higher angles (14° to 18°) for half-blind dovetails.
