There should be roughly one dovetail each 25mm or so across the width. There’s no hard and fast rule so it’s up to the woodworker to use his or her judgement to decide how many are needed. The wood here is 92mm wide and as a consequence I’m going to have three dovetails.For drawers, boxes or trays 2″ or less I generally like a single dovetail. For 3″ to 3 1/2″ and less two dovetails, for 4″ three dovetails, for 5″ to 6″ four dovetails and for 6″ four or possibly five.
How big should dovetails be?
For drawers, boxes or trays 2″ or less I generally like a single dovetail. For 3″ to 3 1/2″ and less two dovetails, for 4″ three dovetails, for 5″ to 6″ four dovetails and for 6″ four or possibly five.
What size are standard dovetails?
Dovetails come in several different types and sizes depending on manufacturer, but the most common are the 11 mm and 3⁄8 inch (9.5 mm). Some other less known, but currently commercially available dovetail mounts, are 12, 13, 13.5, 14, 14.5, 16, 16.5, 17 and 19 mm.
What size dovetail chisels do you really need?
Chisel Sizes – – 12mm / 1/2″ – This will do the majority of your morticing, and come in when cleaning out the pins on those dovetails. – 19mm / 3/4″ (or above) – A nice wide chisel is very useful, and I’d probably aim at an inch, though somewhere between 3/4″ – 1 1/4″ will fit the bill.
What dovetail ratio is best?
Dovetail angles are usually expressed as ratios — the most common being 1:6 and 1:8 (said “one in eight,” and also written as 6:1 or 8:1). As a general rule of thumb: Use 1:6 for softwoods. Use 1:8 for hardwoods.
How big should dovetails be?
For drawers, boxes or trays 2″ or less I generally like a single dovetail. For 3″ to 3 1/2″ and less two dovetails, for 4″ three dovetails, for 5″ to 6″ four dovetails and for 6″ four or possibly five.
What are the rules for dovetail joints?
The general rule is that they measure half the thickness of timber plus around 1 mm along the shoulder line. So these two awl dots are 7 mm in from each edge. These two dots, which mark the corners of the half pins, are now converted into a 1:8 slope at each side.
What is a standard dovetail?
The dovetail joint drawers are typically used to link the edges of a drawer to the front and are known for their tensile strength to being pushed apart. Pins or tongues cut from one board’s end interlock with the groove or tail on the other board’s end.
Are 3 8 and 11mm dovetail the same?
However, that is not the only difference between the two dovetails. They also have different groove angles as shown below. The 11 mm dovetail has a 60-degree angle, while the 3/8” dovetail has a 45-degree angle.
What is the most popular dovetail joint?
The through dovetail joint is the most popular dovetail joint because it is strong, attractive, and versatile. It is commonly used in furniture-making, cabinetry, and woodworking. The through dovetail joint is a traditional woodworking joint characterized by the interlocking triangular shape it creates.
Are dovetail chisels worth it?
The triangular cross-section of these chisels make them ideal for paring and chopping away the waste on dovetail joinery. Suitable for other joinery tasks, these affordable chisels are a nice complement to standard bench chisels for creating and fine-tuning joinery.
Which chisel is best for dovetails?
Fishtail Chisels are perfect for reaching the back corners of half-blind dovetails and paring other hard-to-reach areas. Their unique shape offers versatility for right and left hand recesses.
How thick should a dovetail jig be?
For standard through dovetails, the thickness of the tail stock should be between 8mm to 25mm, and for the pin stock between 8mm and 19mm. For standard half-blind dovetails, stock should be between 12.7mm and 28mm in thickness. When routing standard box joints stock should be between 8mm and 28mm in thickness.
What is the common dovetail ratio?
Anything from 1:6 to 1:9 looks good and works well. Too little rise leaves corners with short grain that easily breaks off, too much rise looks like a poorly made box joint. As long as it looks good, and assembles without breaking, its a good joint.
Are dovetail joints worth it?
Making sure that you pick a drawer joint that can withstand this type of wear and tear is crucial to the longevity of your kitchen cabinets. Dovetail joints are considered one of the strongest joints used in kitchen cabinetry construction and are the best solution for a kitchen cabinet drawer box.
Which is better English or French dovetail?
While both English and French dovetail construction are very sturdy and high quality, English dovetail construction is slightly sturdier with the trade-off of being more expensive and time-consuming to produce.
What is the common dovetail ratio?
Anything from 1:6 to 1:9 looks good and works well. Too little rise leaves corners with short grain that easily breaks off, too much rise looks like a poorly made box joint. As long as it looks good, and assembles without breaking, its a good joint.
How deep should dovetails be?
Try to keep the depth of the dovetail groove between 1/3 and 1/2 the thickness of the part. For example, if the gable of a chest of drawers is 3/4″ thick, machine the dovetail groove between 1/4″ and 3/8″ deep. Any deeper and you will weaken the gable too much.
How thick should a dovetail jig be?
For standard through dovetails, the thickness of the tail stock should be between 8mm to 25mm, and for the pin stock between 8mm and 19mm. For standard half-blind dovetails, stock should be between 12.7mm and 28mm in thickness. When routing standard box joints stock should be between 8mm and 28mm in thickness.
How big should dovetails be?
For drawers, boxes or trays 2″ or less I generally like a single dovetail. For 3″ to 3 1/2″ and less two dovetails, for 4″ three dovetails, for 5″ to 6″ four dovetails and for 6″ four or possibly five.
Should dovetail joints be glued?
Michael Dresdner: The only areas that require glue on dovetails are the diagonal faces. All the diagonal faces are long grain, all the square faces are end grain, and all the flat faces abut end grain. Therefore, you need only apply glue to the diagonal faces on the tails or pins, or both.
What is the weakness of dovetail joint?
The disadvantages of dovetail joints are that they can be fairly difficult to mark out and cut, and if they are made badly these joints lose the advantages listed above. Depending on the project, function, and design, there are a number of different types of dovetail joints to choose from.
How deep should dovetails be?
Try to keep the depth of the dovetail groove between 1/3 and 1/2 the thickness of the part. For example, if the gable of a chest of drawers is 3/4″ thick, machine the dovetail groove between 1/4″ and 3/8″ deep. Any deeper and you will weaken the gable too much.
What is an English dovetail joint?
A dovetail joint is a locking joint. The English dovetail construction tends to allow for the largest possible drawer storage capacity. French dovetail construction is used for more elaborate features such a curved, bowed design.
Are dovetail joints difficult?
This is a relatively complex joint that takes time to fit together. But it’s absolutely within the capabilities of anyone who knows how to use a hand saw. In my opinion, the hardest part is cutting the sides of the pins and tails accurately. Luckily, this is made a lot easier with a good dovetail jig.
What is the most common dovetail angle?
Percy Blandford, who has been writing about woodworking for a long time, writes in “The Woodworker’s Bible” that any angle between 7.5° and 10° is acceptable. The ideal, he says, is 8.5° for softwoods and 7.5° when joining hardwoods.
