Like tenon saws, these can be brass or steel-backed, the main difference is that the steel-backed saws are lighter. You also want to make sure it has 15 PPI or more (slightly smaller teeth) and has a comfortable wooden handle. Paul likes the turned (inline) handle for cutting dovetails, as found on the gent’s saw.
How do I choose a dovetail saw?
Like tenon saws, these can be brass or steel-backed, the main difference is that the steel-backed saws are lighter. You also want to make sure it has 15 PPI or more (slightly smaller teeth) and has a comfortable wooden handle. Paul likes the turned (inline) handle for cutting dovetails, as found on the gent’s saw.
What are the characteristics of a dovetail saw?
What is the best length for a dovetail saw?
Even if you’ll use your saw mostly for run of the mill drawer dovetails, the longer length will give much straighter cuts, and be much faster. It will also help you to see square. Go for around the 10″ (250mm) mark. Maybe a little longer if you work thicker stuff.
Which hand saw is best suited to making a dovetail joint?
You need a saw with rip teeth for dovetail work. This means the cutting edges of the teeth are approximately perpendicular to the length of the saw. Two saws that do the trick are a Japanese dozuki (top) and a Western backsaw.
How do I choose a dovetail saw?
Like tenon saws, these can be brass or steel-backed, the main difference is that the steel-backed saws are lighter. You also want to make sure it has 15 PPI or more (slightly smaller teeth) and has a comfortable wooden handle. Paul likes the turned (inline) handle for cutting dovetails, as found on the gent’s saw.
What is the best length for a dovetail saw?
Even if you’ll use your saw mostly for run of the mill drawer dovetails, the longer length will give much straighter cuts, and be much faster. It will also help you to see square. Go for around the 10″ (250mm) mark. Maybe a little longer if you work thicker stuff.
What is the difference between English dovetail and French dovetail?
English dovetails are the most common. They have interlocking joints and allow the most amount of space – usually several more inches of room than you would get with French dovetails. This is because the dovetail groove cannot be put all the way at the edge of a drawer with French dovetails.
Is dovetail the highest quality?
Without a doubt, dovetail joints are revered as one of the strongest woodworking joints. The strength lies in the precise shaping of the tails and pins. When these elements fit snugly together and are bonded with glue, the resulting joint becomes nearly impossible to pull apart.
What is the difference between a gents saw and a dovetail saw?
On the other hand, the gent’s saw, also referred to as a gentleman’s saw, is a versatile yet smaller hand saw that’s well-suited for a variety of woodworking tasks. It typically has a broader blade compared to a dovetail saw, making it capable of straight or crosscuts in wood.
What is the difference between a dovetail saw and a tenon saw?
Dovetail saws are back saws with a high tooth count, filed for ripping; tenon saws have a lower tooth count and are filed for crosscutting. A mitre saw is filed for crosscutting, is quite a bit longer than a tenon saw and attached to a mitre rig. Most common these days are picture frame saws.
What is the most common dovetail angle?
Percy Blandford, who has been writing about woodworking for a long time, writes in “The Woodworker’s Bible” that any angle between 7.5° and 10° is acceptable. The ideal, he says, is 8.5° for softwoods and 7.5° when joining hardwoods.
Can I use a tenon saw for dovetails?
I find I have greater control with say a ten inch tenon saw and this just happens to be the ideal saw for dovetails too and so I keep my so-called dovetail saw close to hand for the shoulder-cutting aspect of cutting tenons.
Which part of a dovetail do you cut first?
There are only two methods of cutting dovetails by hand: cutting the pins first and cutting the tails, or pin sockets, first. Both methods work. But advocates of each method tend to be passionate about the advantages of their approach and the obvious flaws in the other.1 Feb 1996
Is a dovetail saw a rip saw?
Can you cut dovetails with a jigsaw?
Undoubtedly, you can do the basic cutting with anything that “will fit” and then refine with chisels. That includes a jig saw; preferably one like the Festool or top of the line Bosch that has blade guides.
What is the most popular dovetail joint?
Single-lap Dovetail The single-lap (known to many folks as a half-blind dovetail) is the best known of the dovetails since it’s used to join the front to the sides of a drawer.
What is the difference between a 6 to 1 and 8 to 1 dovetail jig?
Steeper angles like 1:6 give more strength to a joint in softwoods (in theory). The 1:8 angle gives a slimmer look, and because hardwoods are much stronger, it has plenty of hold. 1:8 is my favorite. Here’s how to set a sliding bevel or protractor to the correct dovetail angle (if you don’t have a jig or guide).
How many teeth per inch on dovetail saw?
Too many teeth— One problem with dovetail saws is the number of teeth they have. Most dovetail saws have between 18 and 26 teeth per inch (tpi). Many woodworkers think that the more teeth a dovetail saw has, the smoother it will cut. That’s not necessarily true.1 Dec 1996
What is the most common dovetail ratio?
With regard to what to use, a common recommendation is 1:8 for hardwoods and 1:6 for softwoods. These recommendations are based on some arguments related to strength. However, people use a lot of different ratios depending on application and aesthetics.
What is the type of cutting for a dovetail saw?
Dovetail saws are primarily used for work that require small, very precise cuts, typically in joint making including dovetail and small tenon joints. Available in both rip and cross cut configurations our range of saws from Thomas Flinn, Pax and Veritas are some of the best we have tested.
How do I choose a dovetail saw?
Like tenon saws, these can be brass or steel-backed, the main difference is that the steel-backed saws are lighter. You also want to make sure it has 15 PPI or more (slightly smaller teeth) and has a comfortable wooden handle. Paul likes the turned (inline) handle for cutting dovetails, as found on the gent’s saw.
What is the best length for a dovetail saw?
Even if you’ll use your saw mostly for run of the mill drawer dovetails, the longer length will give much straighter cuts, and be much faster. It will also help you to see square. Go for around the 10″ (250mm) mark. Maybe a little longer if you work thicker stuff.
What are the weaknesses of dovetail?
The disadvantages of dovetail joints are that they can be fairly difficult to mark out and cut, and if they are made badly these joints lose the advantages listed above. Depending on the project, function, and design, there are a number of different types of dovetail joints to choose from.
What is the weakest wood joint?
A butt joint uses a simple technique whereby two pieces of material are joined together at their ends, without any special shaping or cutting. Although it is simple, the butt joint is also the weakest of the wood joinery types.
When did they stop using dovetail?
So manufacturers moved away from dovetails. Hand-cut dovetailing was the default until 1860 when uniform machine-cut joints were introduced. But fine cabinetmakers persisted in fitting their joints by hand until the early 1900s, and cabinetmakers in Europe cut dovetails by hand well into the 1930s.
