Dovetail angles are usually expressed as ratios — the most common being 1:6 and 1:8 (said “one in eight,” and also written as 6:1 or 8:1). As a general rule of thumb: Use 1:6 for softwoods. Use 1:8 for hardwoods.Dovetail angles are usually expressed as ratios — the most common being 1:6 and 1:8 (said “one in eight,” and also written as 6:1 or 8:1). As a general rule of thumb: Use 1:6 for softwoods. Use 1:8 for hardwoods.
What is the best ratio for dovetails?
As regards the ratio to use on various woods, dont get your knickers in a knot. Anything from 1:6 to 1:9 looks good and works well. Too little rise leaves corners with short grain that easily breaks off, too much rise looks like a poorly made box joint.
What are the proportions for a dovetail joint?
The only consistent advice I find is keep dovetail length about equal to board thickness. And keep dovetail ratios between 1:6 and 1:8.
What ratio is a 14 degree dovetail?
This 14° marker equates to a ratio of 1:4. When used with thinner stock, the 14° angle results in a better looking joint. This different angle also gives you a slightly stronger dovetail interlock on the thinner material.
What is 1 to 6 ratio dovetail?
A 1:6 ratio – that’s one unit horizontal with six matching units drawn vertical – lays out as a 9.5 degree angle. A 1:8 ratio – one unit horizontal with eight matching units drawn vertical – is an angle of 7.1 degrees.
What is the standard for a dovetail?
11 mm and 3/8” dovetails are the two most common types of dovetails that you can find on rifles. The 11 mm dovetail represents a standard in Europe, while the 3/8” is a standard in the USA.
What is a standard dovetail angle?
4. The angle of a dovetail joint should be between 7 and 15 degrees: too broad and the joint won’t be strong enough, too skinny, and the pin can snap. So the angle of the dovetail mainly depends on the use and wear the joint will get. Diagram showing dovetail angles vs strength from Fine Woodworking.
What is the best dovetail angle?
Lower (7° to 9°) angles are often advised for joining hardwoods, while higher angles (10° to 14°) are recommended for softwoods and even higher angles (14° to 18°) for half-blind dovetails.
What are the common dovetail sizes?
Dovetail Dado Wood Joints have joint widths of 2/3 and joint depths of 1/2. Wood joints are typically used in wood members with widths between 1.5”-3.5” (3.8-8.9 cm) and depths between of . 75”-3.5” (1.9-8.9 cm).
What is the formula for measuring dovetails?
To obtain dimension x for measuring male dovetails, add 1 to the cotangent of one-half the dovetail angle α, multiply by diameter D of the rods used, and add the product to dimension α.
What is the minimum thickness for a dovetail?
In my own work I aim for a minimum size of 1/4″ and mostly 3/8″. Now that doesn’t mean I won’t go down to less or up too.
How deep should a dovetail joint be?
Typically we use 1 ½” – 2” deep dovetails that are about 2” less deep than the joist, and 4” less deep than the girt – but that is just a starting point – the loads and reactions have to be calculated from there.
Is 11mm dovetail the same as 3 8?
The 3/8 Inch is measured across the bottom of the dovetail whereas the 11 mm is measured across the top of the dovetail. A 3/8 Inch dovetail is about 12.7 mm across the top. The measurements 3/8 and 11mm are not the same for this reason plus the angles are different.
Is dovetail 11mm?
Dovetails come in several different types and sizes depending on manufacturer, but the most common are the 11 mm and 3⁄8 inch (9.5 mm). Some other less known, but currently commercially available dovetail mounts, are 12, 13, 13.5, 14, 14.5, 16, 16.5, 17 and 19 mm.
Are 3 8 and 11mm dovetail the same?
The 3/8 Inch is measured across the bottom of the dovetail whereas the 11 mm is measured across the top of the dovetail. A 3/8 Inch dovetail is about 12.7 mm across the top. The measurements 3/8 and 11mm are not the same for this reason plus the angles are different.
What is the formula for measuring dovetails?
To obtain dimension x for measuring male dovetails, add 1 to the cotangent of one-half the dovetail angle α, multiply by diameter D of the rods used, and add the product to dimension α.
What makes a dovetail joint so strong?
Methods. The dovetail joint is very strong because of the way the ‘tails’ and ‘pins’ are shaped. This makes it difficult to pull the joint apart and virtually impossible when glue is added.
What is the minimum thickness for a dovetail?
In my own work I aim for a minimum size of 1/4″ and mostly 3/8″. Now that doesn’t mean I won’t go down to less or up too.
Which is better English or French dovetail?
While both English and French dovetail construction are very sturdy and high quality, English dovetail construction is slightly sturdier with the trade-off of being more expensive and time-consuming to produce.
What is the difference between English dovetail and French dovetail?
English dovetails are the most common. They have interlocking joints and allow the most amount of space – usually several more inches of room than you would get with French dovetails. This is because the dovetail groove cannot be put all the way at the edge of a drawer with French dovetails.
What are the weaknesses of dovetail?
The disadvantages of dovetail joints are that they can be fairly difficult to mark out and cut, and if they are made badly these joints lose the advantages listed above. Depending on the project, function, and design, there are a number of different types of dovetail joints to choose from.
What is stronger dovetail or finger joint?
Although the finger joint is not mechanically interlocking like a dovetail, the joint is amazingly strong. Today’s modern adhesives and the large glue surface make the finger joint equally as strong as the dovetail throughout the life of the adhesive.
What are the rules for dovetail design?
As a rule of thumb the dovetail’s maximum width should occupy approximately 1/ 2 to 3/ 4 of the gasket’s width (leaving a 1/ 4 – 1/ 8 of gasket width on each side). For larger gasket widths, multiple dovetails can be made side-by- side, facing the same direction or inverted.
Is dovetail joint permanent?
The strongest and most permanent right-angled joints made in wood are the ‘dove-tail’ joints, as illustrated below. The so-called tails and pins fit together to form a secure joint.
Should dovetail joints be glued?
Michael Dresdner: The only areas that require glue on dovetails are the diagonal faces. All the diagonal faces are long grain, all the square faces are end grain, and all the flat faces abut end grain. Therefore, you need only apply glue to the diagonal faces on the tails or pins, or both.
What makes a dovetail joint so strong?
Methods. The dovetail joint is very strong because of the way the ‘tails’ and ‘pins’ are shaped. This makes it difficult to pull the joint apart and virtually impossible when glue is added.
