With regard to what to use, a common recommendation is 1:8 for hardwoods and 1:6 for softwoods. These recommendations are based on some arguments related to strength. However, people use a lot of different ratios depending on application and aesthetics.
What is the standard dovetail ratio?
Dovetail angles are usually expressed as ratios — the most common being 1:6 and 1:8 (said “one in eight,” and also written as 6:1 or 8:1). As a general rule of thumb: Use 1:6 for softwoods. Use 1:8 for hardwoods.
What ratio is a 14 degree dovetail?
Commonly accepted ratios are 1:8 for hardwoods and 1:6 for softer timber. This 14° marker equates to a ratio of 1:4. When used with thinner stock, the 14° angle results in a better looking joint.
What is the slope of a dovetail joint?
There are different types of dovetail joints. The angle of slope varies according to the wood used, purpose of joint and type of work. Typically the slope is 1:6 for softwoods, and a shallower 1:8 slope for hardwoods. Often a slope of 1:7 is used as a compromise.
What is the ratio of tail to pin in a dovetail joint?
The line between that end point and starting point will be the angle of your tail and pin sides. 6:1 (9.5°) and 8:1 (7.1°) dovetail ratios are the most common (though you’ll often see 4:1 and 10:1 as well).
What is 1 to 6 ratio dovetail?
A 1:6 ratio – that’s one unit horizontal with six matching units drawn vertical – lays out as a 9.5 degree angle. A 1:8 ratio – one unit horizontal with eight matching units drawn vertical – is an angle of 7.1 degrees.
What is the most common dovetail angle?
Percy Blandford, who has been writing about woodworking for a long time, writes in “The Woodworker’s Bible” that any angle between 7.5° and 10° is acceptable. The ideal, he says, is 8.5° for softwoods and 7.5° when joining hardwoods.
What is the best angle for a dovetail joint?
Lower (7° to 9°) angles are often advised for joining hardwoods, while higher angles (10° to 14°) are recommended for softwoods and even higher angles (14° to 18°) for half-blind dovetails.
What are common dovetail sizes?
What are the rules for dovetail joints?
The general rule is that they measure half the thickness of timber plus around 1 mm along the shoulder line. So these two awl dots are 7 mm in from each edge. These two dots, which mark the corners of the half pins, are now converted into a 1:8 slope at each side.
What are the 2 types of dovetail joints?
Types of Dovetail Joints Half-Blind dovetails: In these, the pins and tails are hidden. Half-blind dovetails are only revealed when moved, opened or seen from a certain angle, like behind a drawer face. In a through dovetail, both the dovetails and pins are visible.
How deep should a dovetail joint be?
Typically we use 1 ½” – 2” deep dovetails that are about 2” less deep than the joist, and 4” less deep than the girt – but that is just a starting point – the loads and reactions have to be calculated from there.
What is the minimum thickness for a dovetail?
Structurally I have looked for pin strength in dovetails as the dovetailed aspect is always strong because it is always at least as wide and mostly wider than the pins. In my own work I aim for a minimum size of 1/4″ and mostly 3/8″.
How do you mark a dovetail?
Mark out the two ‘half-pins’ at the edges on the first piece of wood. The ‘pins’ are the bits of wood between the tails so there are two half-pins; one each side. The general rule is that they measure half the thickness of timber plus around a mm, so the two dots on the shoulder line are 7mm in from each edge.
Is 11mm dovetail the same as 3 8?
However, that is not the only difference between the two dovetails. They also have different groove angles as shown below. The 11 mm dovetail has a 60-degree angle, while the 3/8” dovetail has a 45-degree angle.
What is the difference between 11mm and 3 8 dovetail?
The 3/8 Inch is measured across the bottom of the dovetail whereas the 11 mm is measured across the top of the dovetail. A 3/8 Inch dovetail is about 12.7 mm across the top. The measurements 3/8 and 11mm are not the same for this reason plus the angles are different.
What size are standard dovetails?
Dovetails come in several different types and sizes depending on manufacturer, but the most common are the 11 mm and 3⁄8 inch (9.5 mm). Some other less known, but currently commercially available dovetail mounts, are 12, 13, 13.5, 14, 14.5, 16, 16.5, 17 and 19 mm.
What are the measurements for a dovetail?
DoveTail Description: 60 degree dove tail, approximately 1-inch tall and 4-inches across the tail corners and uses a 1/4-inch thick gib plate on one side. Guessing dimensions will be: depth(s), pin diameter, and dimension across/between pins.
What is the difference between 11mm and 3 8 dovetail?
The 3/8 Inch is measured across the bottom of the dovetail whereas the 11 mm is measured across the top of the dovetail. A 3/8 Inch dovetail is about 12.7 mm across the top. The measurements 3/8 and 11mm are not the same for this reason plus the angles are different.
What are typical dovetail angles?
Although softwoods are more compressible than hardwoods, you needn’t change the dovetail angle to add strength to the joint. Any angle between 7° and 15° will work, regardless of the wood. But stay within that range.
Which is better English or French dovetail?
While both English and French dovetail construction are very sturdy and high quality, English dovetail construction is slightly sturdier with the trade-off of being more expensive and time-consuming to produce.
What is the most popular dovetail joint?
Single-lap Dovetail The single-lap (known to many folks as a half-blind dovetail) is the best known of the dovetails since it’s used to join the front to the sides of a drawer.
What are the weaknesses of dovetail?
The disadvantages of dovetail joints are that they can be fairly difficult to mark out and cut, and if they are made badly these joints lose the advantages listed above. Depending on the project, function, and design, there are a number of different types of dovetail joints to choose from.
What is stronger dovetail or finger joint?
The interlocking design of the dovetail creates a strong bond that can withstand a lot of stress. On the other hand, a box joint, also known as a finger joint, is strong in terms of sheer surface area and glue surface, making it suitable for joining the corners of a box or a drawer.
Which part of a dovetail do you cut first?
Cutting the dovetail pins first makes sense. It’s easier to hold the pin board in place to mark the tails than it is to hold the tail board against the end of what will be the pin board. Also, the walls of the pins provide a good surface for the awl as you mark the tails.1 Feb 1996
Are dovetail joints worth it?
Dovetail drawers are known for their durability. The joint’s design provides exceptional resistance to the stresses of heavy items, making them ideal for storing dishes, pots, and pans. The construction of dovetail drawers ensures that they will not come apart easily, even with frequent use.
