The minimum recommended pin board thickness is 1⁄2″[13mm]. Remember, the No 128 cutters rout at 3⁄8″[9,5mm] deep. If you wish to rout a pin board less than the minimum thickness ➀, it will be necessary to pack the board up from the jig body. We suggest using a piece of 1⁄4″ to 3⁄8″[6 to 9mm] plywood for this purpose ➁.
What is the minimum thickness for a dovetail?
In my own work I aim for a minimum size of 1/4″ and mostly 3/8″. Now that doesn’t mean I won’t go down to less or up too.
What is the standard for a dovetail?
As a rule of thumb the dovetail’s maximum width should occupy approximately 1/ 2 to 3/ 4 of the gasket’s width (leaving a 1/ 4 – 1/ 8 of gasket width on each side). For larger gasket widths, multiple dovetails can be made side-by- side, facing the same direction or inverted.
How thick should a dovetail jig be?
Dovetail Jig rave about the user-friendly features. The jig’s patented alignment lines and router bit-depth stop simplify set up and get you up and running in no time. This versatile jig accepts stock from 1/4 to 1-1/8 inch in thickness and up to 12 inches in width.
What are the rules for dovetails?
Is dovetail 11mm?
Dovetails come in several different types and sizes depending on manufacturer, but the most common are the 11 mm and 3⁄8 inch (9.5 mm). Some other less known, but currently commercially available dovetail mounts, are 12, 13, 13.5, 14, 14.5, 16, 16.5, 17 and 19 mm.
Can you make dovetail joints with plywood?
A wide variety of methods can be used to make dovetail plywood drawer boxes. They are generally considered by the woodworking industry as time-consuming and difficult to make. The dovetails can be cut by hand with a dovetailing saw and chisel or you can use a dovetail jig and router.
Are 3 8 and 11mm dovetail the same?
The 3/8 Inch is measured across the bottom of the dovetail whereas the 11 mm is measured across the top of the dovetail. A 3/8 Inch dovetail is about 12.7 mm across the top. The measurements 3/8 and 11mm are not the same for this reason plus the angles are different.
What are the common dovetail sizes?
Dovetail Dado Wood Joints have joint widths of 2/3 and joint depths of 1/2. Wood joints are typically used in wood members with widths between 1.5”-3.5” (3.8-8.9 cm) and depths between of . 75”-3.5” (1.9-8.9 cm).
What is the most popular dovetail?
1) Through Dovetail Also known as the plain dovetail, this is the most common and basic type of dovetail joint. Through interlocking tails and pins, this joint showcases consistent angles, revealing the wood’s end grains on external surfaces.
Can I make my own dovetail jig?
All you need is some standard, off-the-shelf hardware, 5 board feet of hardwood , and a piece of hardboard to make your own “comb” template. However, as I got into the project further I found some improvements I could make over manufactured dovetail jigs along the way.
Do you need to glue dovetail joints?
Michael Dresdner: The only areas that require glue on dovetails are the diagonal faces. All the diagonal faces are long grain, all the square faces are end grain, and all the flat faces abut end grain. Therefore, you need only apply glue to the diagonal faces on the tails or pins, or both.
How deep should dovetails be?
Try to keep the depth of the dovetail groove between 1/3 and 1/2 the thickness of the part. For example, if the gable of a chest of drawers is 3/4″ thick, machine the dovetail groove between 1/4″ and 3/8″ deep. Any deeper and you will weaken the gable too much.
Can you cut dovetails with a jigsaw?
If you have a jigsaw table, a few simple angle jigs can help you create fast, precise and repeatable dovetails.
What is the best wood to practice dovetails on?
Soft maple, or red maple, can be a great wood to practice dovetails on.
Are 3 8 and 11mm dovetail the same?
The 3/8 Inch is measured across the bottom of the dovetail whereas the 11 mm is measured across the top of the dovetail. A 3/8 Inch dovetail is about 12.7 mm across the top. The measurements 3/8 and 11mm are not the same for this reason plus the angles are different.
What are the common dovetail sizes?
Dovetail Dado Wood Joints have joint widths of 2/3 and joint depths of 1/2. Wood joints are typically used in wood members with widths between 1.5”-3.5” (3.8-8.9 cm) and depths between of . 75”-3.5” (1.9-8.9 cm).
What are the limitations of a dovetail joint?
The disadvantages of dovetail joints are that they can be fairly difficult to mark out and cut, and if they are made badly these joints lose the advantages listed above. Depending on the project, function, and design, there are a number of different types of dovetail joints to choose from.
What is the most common dovetail ratio?
Dovetail angles are usually expressed as ratios — the most common being 1:6 and 1:8 (said “one in eight,” and also written as 6:1 or 8:1). As a general rule of thumb: Use 1:6 for softwoods. Use 1:8 for hardwoods.
Can you cut dovetails with a jigsaw?
If you have a jigsaw table, a few simple angle jigs can help you create fast, precise and repeatable dovetails.
Which is better English or French dovetail?
While both English and French dovetail construction are very sturdy and high quality, English dovetail construction is slightly sturdier with the trade-off of being more expensive and time-consuming to produce.
What is stronger dovetail or finger joint?
Although the finger joint is not mechanically interlocking like a dovetail, the joint is amazingly strong. Today’s modern adhesives and the large glue surface make the finger joint equally as strong as the dovetail throughout the life of the adhesive.
What is the weakness of dovetail joint?
The disadvantages of dovetail joints are that they can be fairly difficult to mark out and cut, and if they are made badly these joints lose the advantages listed above. Depending on the project, function, and design, there are a number of different types of dovetail joints to choose from.
Is dovetail joint permanent?
The strongest and most permanent right-angled joints made in wood are the ‘dove-tail’ joints, as illustrated below. The so-called tails and pins fit together to form a secure joint.
What is the common angle for a dovetail joint?
Although softwoods are more compressible than hardwoods, you needn’t change the dovetail angle to add strength to the joint. Any angle between 7° and 15° will work, regardless of the wood. But stay within that range. If you go below 7°, you’ll start to lose the mechanical strength of the dovetail.
Is a box joint stronger than a dovetail?
For this test, the box joint proved stronger. Plus, the box joint is strong in both directions, whereas the dovetails are useful only for pulling from one piece, but not the other. So really, to use a dovetail joint for the sake of strength is obsolete, mostly on account of the strength of wood glues.
