you; we recommend at least 8mm shanks, but 1⁄2″ would be even better, with of course the appropriate guide- bush. If you have to use 1⁄4″ shanks in hardwood, use a second router to rough out the slot centre with a straight cutter. We recommend 5⁄8″[15,9mm] as the min- imum size guidebush for sliding dovetails.
How thick should dovetails be?
Structurally I have looked for pin strength in dovetails as the dovetailed aspect is always strong because it is always at least as wide and mostly wider than the pins. In my own work I aim for a minimum size of 1/4″ and mostly 3/8″.
What are the rules for a dovetail joint?
The general rule is that they measure half the thickness of timber plus around 1 mm along the shoulder line. So these two awl dots are 7 mm in from each edge. These two dots, which mark the corners of the half pins, are now converted into a 1:8 slope at each side.
How thick should a dovetail jig be?
Dovetail Jig rave about the user-friendly features. The jig’s patented alignment lines and router bit-depth stop simplify set up and get you up and running in no time. This versatile jig accepts stock from 1/4 to 1-1/8 inch in thickness and up to 12 inches in width.
What are the common dovetail sizes?
Dovetails come in several different types and sizes depending on manufacturer, but the most common are the 11 mm and 3⁄8 inch (9.5 mm). Some other less known, but currently commercially available dovetail mounts, are 12, 13, 13.5, 14, 14.5, 16, 16.5, 17 and 19 mm.
How thick should dovetails be?
Structurally I have looked for pin strength in dovetails as the dovetailed aspect is always strong because it is always at least as wide and mostly wider than the pins. In my own work I aim for a minimum size of 1/4″ and mostly 3/8″.
Are 3 8 and 11mm dovetail the same?
However, that is not the only difference between the two dovetails. They also have different groove angles as shown below. The 11 mm dovetail has a 60-degree angle, while the 3/8” dovetail has a 45-degree angle.
Can you put dovetails in plywood?
Though it isn’t a very good choice for plywood either, glued finger joints should offer better strength. Dovetails provide very little long grain to long grain gluing surfaces in plywood. There are other things to consider with plywood also such as the number of plies & voids.
Should dovetail joints be glued?
Michael Dresdner: The only areas that require glue on dovetails are the diagonal faces. All the diagonal faces are long grain, all the square faces are end grain, and all the flat faces abut end grain. Therefore, you need only apply glue to the diagonal faces on the tails or pins, or both.
What is the weakness of dovetail joint?
The disadvantages of dovetail joints are that they can be fairly difficult to mark out and cut, and if they are made badly these joints lose the advantages listed above. Depending on the project, function, and design, there are a number of different types of dovetail joints to choose from.
Is dovetail joint permanent?
The strongest and most permanent right-angled joints made in wood are the ‘dove-tail’ joints, as illustrated below. The so-called tails and pins fit together to form a secure joint.
What is the most common dovetail ratio?
Dovetail angles are usually expressed as ratios — the most common being 1:6 and 1:8 (said “one in eight,” and also written as 6:1 or 8:1). As a general rule of thumb: Use 1:6 for softwoods. Use 1:8 for hardwoods.
Can I make my own dovetail jig?
All you need is some standard, off-the-shelf hardware, 5 board feet of hardwood , and a piece of hardboard to make your own “comb” template. However, as I got into the project further I found some improvements I could make over manufactured dovetail jigs along the way.
Is dovetail 11mm?
The standard 22 tip-off dovetail in the US is 3/8″ at the bottom and up to 1/2″ at the top. The European 11mm dovetail is typically 11mm at the top and perhaps 8mm at the bottom. The 11mm dovetail typically has a 60 degree angle from the bottom inside corner to the top where the 3/8″ is typically 45 degrees.
What is a standard dovetail?
A series of pins cut to extend from the end of one board interlock with a series of ‘tails’ cut into the end of another board. The pins and tails have a trapezoidal shape. Once glued, a wooden dovetail joint requires no mechanical fasteners.
What is the best angle for a dovetail?
Percy Blandford, who has been writing about woodworking for a long time, writes in “The Woodworker’s Bible” that any angle between 7.5° and 10° is acceptable. The ideal, he says, is 8.5° for softwoods and 7.5° when joining hardwoods.
What is a good ratio for dovetails?
D) MARK DOWN TO YOUR MARKING GAUGE LINE Now it’s time to decide on a dovetail ratio, or angle. If you have one of my dovetail jigs, you can skip ahead to Step 4. Dovetail angles are usually expressed as ratios — the most common being 1:6 and 1:8 (said “one in eight,” and also written as 6:1 or 8:1).
What is the common dovetail ratio?
Anything from 1:6 to 1:9 looks good and works well. Too little rise leaves corners with short grain that easily breaks off, too much rise looks like a poorly made box joint.
What is a standard dovetail?
A series of pins cut to extend from the end of one board interlock with a series of ‘tails’ cut into the end of another board. The pins and tails have a trapezoidal shape. Once glued, a wooden dovetail joint requires no mechanical fasteners.
What is the ideal dovetail angle?
Lower (7° to 9°) angles are often advised for joining hardwoods, while higher angles (10° to 14°) are recommended for softwoods and even higher angles (14° to 18°) for half-blind dovetails.
How thick should dovetails be?
Structurally I have looked for pin strength in dovetails as the dovetailed aspect is always strong because it is always at least as wide and mostly wider than the pins. In my own work I aim for a minimum size of 1/4″ and mostly 3/8″.
What rifles have 11mm dovetail?
Is dovetail the strongest joint?
Dovetail is arguably the strongest joint in millwork. It’s made so that it can’t be twisted or pulled in any direction except for one. This means that it’ll take more force to break or damage the joint. Because of the preciseness of each piece, this joint is held into place without the need for extra reinforcement.
Can I use pine for dovetails?
Pine. While pine is commonly used as drawer sides, it’s not the best to practice good dovetail technique with. You need scary sharp chisels just to pare it properly.
What wood is best for dovetails?
For practicing hand cut dovetails, poplar hardwood is very good as it is much finer than pine, it is forgiving, easy to saw and compressible. Once you have mastered the hand cut dovetail, you can move on to harder woods for the drawer sides. The drawer front should be harder regardless.
Is pine good for dovetails?
Try a few in pine, but if you want to have useful practice you need to be using hardwoods. That is because pine compresses easily so is both forgiving and frustrating. To keep the cost down you could try poplar? Not a true hardwood but much harder than pine.
