A 1:6 ratio – that’s one unit horizontal with six matching units drawn vertical – lays out as a 9.5 degree angle. A 1:8 ratio – one unit horizontal with eight matching units drawn vertical – is an angle of 7.1 degrees.
What is the ratio of a dovetail to an angle?
Dovetail angles are usually expressed as ratios — the most common being 1:6 and 1:8 (said “one in eight,” and also written as 6:1 or 8:1). As a general rule of thumb: Use 1:6 for softwoods. Use 1:8 for hardwoods.
What ratio is a 14 degree dovetail?
There is no hard and fast rule when it comes to dovetail angles. Commonly accepted ratios are 1:8 for hardwoods and 1:6 for softer timber. This 14° marker equates to a ratio of 1:4.
What angle should a dovetail joint be?
The angle of a dovetail joint should be between 7 and 15 degrees: too broad and the joint won’t be strong enough, too skinny, and the pin can snap. So the angle of the dovetail mainly depends on the use and wear the joint will get. 5. They are called ‘dovetails’ because they are shaped like the tail feathers of a dove!
What is the ratio of pin to tail for dovetail joints?
The line between that end point and starting point will be the angle of your tail and pin sides. 6:1 (9.5°) and 8:1 (7.1°) dovetail ratios are the most common (though you’ll often see 4:1 and 10:1 as well).
What is the angle of a 11mm dovetail?
The 11 mm dovetail has a 60-degree angle, while the 3/8” dovetail has a 45-degree angle.
What are the typical angles of dovetail markers?
Dovetail angles are expressed in two ways: as ratios and degrees. 1:8 roughly translates to 70 and 1:6 translates roughly as 90. These days, we often hear that 90 is recommended for softwoods, while 70 should be used for hardwoods.
What is a standard dovetail?
A series of pins cut to extend from the end of one board interlock with a series of ‘tails’ cut into the end of another board. The pins and tails have a trapezoidal shape. Once glued, a wooden dovetail joint requires no mechanical fasteners.
What are the measurements for a dovetail?
Fine work the pins 4mm > 6mm, larger work 7mm > 12mm. To have a desirable appearance the pins smaller than the tails. Your tails should be around 18mm > 35mm for fine work like drawers and 35mm > 55mm on larger work like a chest. Decide on your tail size remembering “One more tail than pin”.
What are common dovetail sizes?
Dovetails come in several different types and sizes depending on manufacturer, but the most common are the 11 mm and 3⁄8 inch (9.5 mm). Some other less known, but currently commercially available dovetail mounts, are 12, 13, 13.5, 14, 14.5, 16, 16.5, 17 and 19 mm.
What dovetail ratio is best?
As regards the ratio to use on various woods, dont get your knickers in a knot. Anything from 1:6 to 1:9 looks good and works well. Too little rise leaves corners with short grain that easily breaks off, too much rise looks like a poorly made box joint.
What is the most common dovetail angle?
Percy Blandford, who has been writing about woodworking for a long time, writes in “The Woodworker’s Bible” that any angle between 7.5° and 10° is acceptable. The ideal, he says, is 8.5° for softwoods and 7.5° when joining hardwoods.
What is the strongest angle for a dovetail?
Lower (7° to 9°) angles are often advised for joining hardwoods, while higher angles (10° to 14°) are recommended for softwoods and even higher angles (14° to 18°) for half-blind dovetails.
What is the weakness of dovetail joint?
The disadvantages of dovetail joints are that they can be fairly difficult to mark out and cut, and if they are made badly these joints lose the advantages listed above. Depending on the project, function, and design, there are a number of different types of dovetail joints to choose from.
What is stronger dovetail or finger joint?
Although the finger joint is not mechanically interlocking like a dovetail, the joint is amazingly strong. Today’s modern adhesives and the large glue surface make the finger joint equally as strong as the dovetail throughout the life of the adhesive.
What is the minimum thickness for a dovetail?
Structurally I have looked for pin strength in dovetails as the dovetailed aspect is always strong because it is always at least as wide and mostly wider than the pins. In my own work I aim for a minimum size of 1/4″ and mostly 3/8″.
What are the measurements for a dovetail?
Fine work the pins 4mm > 6mm, larger work 7mm > 12mm. To have a desirable appearance the pins smaller than the tails. Your tails should be around 18mm > 35mm for fine work like drawers and 35mm > 55mm on larger work like a chest. Decide on your tail size remembering “One more tail than pin”.
What is the formula for measuring dovetails?
To obtain dimension x for measuring male dovetails, add 1 to the cotangent of one-half the dovetail angle α, multiply by diameter D of the rods used, and add the product to dimension α.
What is the formula for the angle of the internal dovetail?
Explanation: Formula for finding the angle of an internal dovetail is Tan A = (l2-l1/2) / h where l1 and l2 are the distance across the pins and h is the height of slip gauges. Thus by knowing these three parameters, angle A can be calculated.
What is the average size of a dovetail?
Dovetails come in several different types and sizes depending on manufacturer, but the most common are the 11 mm and 3⁄8 inch (9.5 mm). Some other less known, but currently commercially available dovetail mounts, are 12, 13, 13.5, 14, 14.5, 16, 16.5, 17 and 19 mm.
What is the formula for the angle of the internal dovetail?
Explanation: Formula for finding the angle of an internal dovetail is Tan A = (l2-l1/2) / h where l1 and l2 are the distance across the pins and h is the height of slip gauges. Thus by knowing these three parameters, angle A can be calculated.
How do you mark out a dovetail joint?
Mark out the two ‘half-pins’ at the edges on the first piece of wood. The ‘pins’ are the bits of wood between the tails so there are two half-pins; one each side. The general rule is that they measure half the thickness of timber plus around a mm, so the two dots on the shoulder line are 7mm in from each edge.
What are the rules for a dovetail joint?
The general rule is that they measure half the thickness of timber plus around 1 mm along the shoulder line. So these two awl dots are 7 mm in from each edge. These two dots, which mark the corners of the half pins, are now converted into a 1:8 slope at each side.
What is an English dovetail joint?
What is the most popular dovetail joint?
Single-lap Dovetail The single-lap (known to many folks as a half-blind dovetail) is the best known of the dovetails since it’s used to join the front to the sides of a drawer.
Which is better English or French dovetail?
While both English and French dovetail construction are very sturdy and high quality, English dovetail construction is slightly sturdier with the trade-off of being more expensive and time-consuming to produce.
