The ideal, he says, is 8.5° for softwoods and 7.5° when joining hardwoods. My Own Eye. One Wednesday morning I laid out and cut a bunch of these dovetails. I ignored the really shallow angles (6.5° to 8.5°) because I wanted to adopt something more angular. The 10° dovetails looked OK.
What is the most common angle for a dovetail?
Percy Blandford, who has been writing about woodworking for a long time, writes in “The Woodworker’s Bible” that any angle between 7.5° and 10° is acceptable. The ideal, he says, is 8.5° for softwoods and 7.5° when joining hardwoods.
What degrees are dovetails?
Although softwoods are more compressible than hardwoods, you needn’t change the dovetail angle to add strength to the joint. Any angle between 7° and 15° will work, regardless of the wood. But stay within that range. If you go below 7°, you’ll start to lose the mechanical strength of the dovetail.
What is the standard dovetail ratio?
Dovetail angles are usually expressed as ratios — the most common being 1:6 and 1:8 (said “one in eight,” and also written as 6:1 or 8:1). As a general rule of thumb: Use 1:6 for softwoods. Use 1:8 for hardwoods.
What is the most common angle for a dovetail?
Percy Blandford, who has been writing about woodworking for a long time, writes in “The Woodworker’s Bible” that any angle between 7.5° and 10° is acceptable. The ideal, he says, is 8.5° for softwoods and 7.5° when joining hardwoods.
What degrees are dovetails?
Although softwoods are more compressible than hardwoods, you needn’t change the dovetail angle to add strength to the joint. Any angle between 7° and 15° will work, regardless of the wood. But stay within that range. If you go below 7°, you’ll start to lose the mechanical strength of the dovetail.
Is 11mm dovetail the same as 3 8?
However, that is not the only difference between the two dovetails. They also have different groove angles as shown below. The 11 mm dovetail has a 60-degree angle, while the 3/8” dovetail has a 45-degree angle.
What is angle 1 to 8 dovetail?
A 1:8 ratio – one unit horizontal with eight matching units drawn vertical – is an angle of 7.1 degrees.
What are the rules for dovetail?
What are the rules for dovetail joints?
The general rule is that they measure half the thickness of timber plus around 1 mm along the shoulder line. So these two awl dots are 7 mm in from each edge. These two dots, which mark the corners of the half pins, are now converted into a 1:8 slope at each side.
What ratio is a 14 degree dovetail?
This 14° marker equates to a ratio of 1:4. When used with thinner stock, the 14° angle results in a better looking joint. This different angle also gives you a slightly stronger dovetail interlock on the thinner material.
What are common dovetail sizes?
How deep should a dovetail joint be?
so with our current scenario of 3″ we would have 2 x 3/16″ = 3/8″ plus the full pin of 3/8″ so 3/4″ pin accumulation. This then leaves 2 1/4″ for two tails so 1 1/8″ dovetails. As I said, for me, generally, I simply use 3/8″ equally for all of my pins as my standard size in my more general work.
What is the most common angle cut?
The most common angle is the 45 ° angle.
What ratio is a 14 degree dovetail?
This 14° marker equates to a ratio of 1:4. When used with thinner stock, the 14° angle results in a better looking joint. This different angle also gives you a slightly stronger dovetail interlock on the thinner material.
Is dovetail 11mm?
Dovetails come in several different types and sizes depending on manufacturer, but the most common are the 11 mm and 3⁄8 inch (9.5 mm). Some other less known, but currently commercially available dovetail mounts, are 12, 13, 13.5, 14, 14.5, 16, 16.5, 17 and 19 mm.
What is the best angle for sliding dovetails?
A steeper angle adds reliability in softwood, and narrow stock calls for a narrow bit. We use a bit with a 1⁄ 2 ” cutting diameter and a 14° angle to make sliding dovetail joints in 3⁄ 4 ” hardwood.
What is the most common angle for a dovetail?
Percy Blandford, who has been writing about woodworking for a long time, writes in “The Woodworker’s Bible” that any angle between 7.5° and 10° is acceptable. The ideal, he says, is 8.5° for softwoods and 7.5° when joining hardwoods.
What degrees are dovetails?
Although softwoods are more compressible than hardwoods, you needn’t change the dovetail angle to add strength to the joint. Any angle between 7° and 15° will work, regardless of the wood. But stay within that range. If you go below 7°, you’ll start to lose the mechanical strength of the dovetail.
Is dovetail the strongest joint?
The advantages of the dovetail joint are that it is the strongest of all joints, has a large gluing area, is interlocking, resists being pulled apart, looks attractive, and would hold together even without glue.
What size dovetail is CZ 452?
Our hd cz 452 mount is available for 3/8″ and 11mm dovetails.
How do you find the angle of a dovetail slot?
You could take an over or between pins measurements if it’s the male or female part. Take 2 measurements using 2 different diameter pair of pins. Assuming the edges are fairly straight you should be able to deduce the dovetail angle.
What is the difference between English dovetail and French dovetail?
French dovetails have sliding joints and are shorter in height. A piece of furniture with a curved front will always have French dovetails, because English dovetails will not work with that shape.
What size chisels for dovetails?
After years of dovetailing, I noticed that two of my chisels were seeing almost all the action: the 1/4″-wide and a 3/4″-wide tools. I use the narrow one for removing waste between the tails and the larger one for removing waste between pins.
Do you need to clamp dovetails?
Well cut dovetails don’t need clamps, but it’s always nice to have clamps and cauls laid out just in case. I also like to have a piece of wood slightly thinner than my tails to use to tap the tails together to make sure they are fully seated. Before walking away, I check the case for square, then let the glue sit.
Should dovetail joints be glued?
Michael Dresdner: The only areas that require glue on dovetails are the diagonal faces. All the diagonal faces are long grain, all the square faces are end grain, and all the flat faces abut end grain. Therefore, you need only apply glue to the diagonal faces on the tails or pins, or both.
