They are still used, but nowadays more from tradition and a desire to show craftsmanship than anything else. The dovetail evolved as a way to keep box corner joints together using the poor boiled-hooves-and-hide glues then available. The shape of the joint provides some mechanical locking in the corner.
When did they stop using dovetail joints?
By 1730, through dovetail joinery was abandoned in English furniture making in favor of the lapped construction. As furniture became more refined, furniture makers began to take pride in the construction of their drawers as well.
Are dovetail joints worth it?
Making sure that you pick a drawer joint that can withstand this type of wear and tear is crucial to the longevity of your kitchen cabinets. Dovetail joints are considered one of the strongest joints used in kitchen cabinetry construction and are the best solution for a kitchen cabinet drawer box.
What are the cons of a dovetail joint?
The disadvantages of dovetail joints are that they can be fairly difficult to mark out and cut, and if they are made badly these joints lose the advantages listed above. Depending on the project, function, and design, there are a number of different types of dovetail joints to choose from.
Where are dovetail joints commonly used?
A dovetail joint or simply dovetail is a joinery technique most commonly used in woodworking joinery (carpentry), including furniture, cabinets, log buildings, and traditional timber framing.
What is stronger dovetail or finger joint?
Although the finger joint is not mechanically interlocking like a dovetail, the joint is amazingly strong. Today’s modern adhesives and the large glue surface make the finger joint equally as strong as the dovetail throughout the life of the adhesive.
Are dovetails the strongest of all joints?
Dovetail is arguably the strongest joint in millwork. It’s made so that it can’t be twisted or pulled in any direction except for one. This means that it’ll take more force to break or damage the joint. Because of the preciseness of each piece, this joint is held into place without the need for extra reinforcement.
Do dovetail joints need to be glued?
Michael Dresdner: The only areas that require glue on dovetails are the diagonal faces. All the diagonal faces are long grain, all the square faces are end grain, and all the flat faces abut end grain. Therefore, you need only apply glue to the diagonal faces on the tails or pins, or both.
How difficult is a dovetail joint?
Hand-cutting a dovetail joint is kind of a woodworking high-wire act; one slip of the saw or chisel and the joint either won’t fit together or will look sloppy. It takes a lot of time to master the ability to cut dovetails quickly and well (by hand or machine), without a lot of fussing around.
Are dovetail joints permanent?
The strongest and most permanent right-angled joints made in wood are the ‘dove-tail’ joints, as illustrated below. The so-called tails and pins fit together to form a secure joint.
Can you use dovetail joints with plywood?
A wide variety of methods can be used to make dovetail plywood drawer boxes. They are generally considered by the woodworking industry as time-consuming and difficult to make. The dovetails can be cut by hand with a dovetailing saw and chisel or you can use a dovetail jig and router.
Why are dovetail joints so strong?
Strong: The interlocking tails and pins resist force in all directions but one. They also provide many faces for glue to adhere, strengthening the joint even more. Displays quality work: If you want to impress someone or charge a little more for your work, visible dovetails are a good way to do it.
Is dovetail the highest quality?
Without a doubt, dovetail joints are revered as one of the strongest woodworking joints. The strength lies in the precise shaping of the tails and pins. When these elements fit snugly together and are bonded with glue, the resulting joint becomes nearly impossible to pull apart.
What is the strongest joint in woodworking?
Mortise and tenon joints are widely regarded as one of the strongest and most reliable woodworking joints. They involve creating a mortise, or a hole, in one piece of wood and a tenon on the end of the other piece, which fits into the mortise.
Are dovetail joints antique?
Most quality pieces of antique furniture will have a dovetail joint in the drawer construction as it was a very early form of construction, but was so successful, it was used for many 100’s of years. The Dovetail joint, got its name because of its similarity to the shape of a birds tail.
How deep should a dovetail joint be?
Typically we use 1 ½” – 2” deep dovetails that are about 2” less deep than the joist, and 4” less deep than the girt – but that is just a starting point – the loads and reactions have to be calculated from there.
How do you date a dovetail joint?
You can get an idea of the date of a piece of antique furniture by looking at the dovetail joint, as if it is hand cut you know its pre 1880 and the more primitive the cut usually means an earlier piece. Below you can see examples, the first is a 17th century drawer, pre dovetail so very primitive clout nails used.
How can you tell if wood is antique furniture?
The best way to tell if it’s real wood is to look at the end grain. This is the surface of the wood that is exposed when a piece of wood is cut across the growth rings or layers of the tree. Real wood’s end grain looks distinctly different from that of manufactured wood.
How can you tell how old a chest of drawers is?
Look at the bottom board’s grain as well; if it runs from front to back, the chest was likely built in the early 18th century; if it runs from side to side, it was presumably made after 1750. The chest’s handles should also be examined to see if they are authentic.
How can you tell how old furniture is?
Search for any labels, stamps or manufacturing tags underneath or on the back of furniture, or in the drawers. These marks will be able to tell you who made the furniture, where it was manufactured and often the year that it was made. If there is a label, look for signs of ageing as they can be faked.
What is the hardest joint in carpentry?
A mortice and tenon joint is generally recognised as the toughest around. As a result, they are sensible to use for commercial joinery projects. In simple terms, it allows two pieces of wood to be connected together.
Is a box joint stronger than a dovetail?
It depends on the application. For box joint, some people put a lot more fingers than it is possible to do with Dovetail. In this case, the gluing surface is larger, and the joint is likely stronger. Also, some find a way to hide a finish nail in the joint.
What is the best corner joint for woodworking?
THE DOVETAIL JOINT Dovetail joints are very strong and resist pulling apart through the use of wedge-shaped interlocking pieces (the wedges resemble a dove’s tail). Dovetail joints are found where the ends of two pieces of wood meet at a right angle, such as along the corners of drawer sides.
What is the strongest corner joint?
Mortise and tenon joints have stood the test of time for their remarkable strength.
Can you make a dovetail joint by hand?
Of the four types of dovetail joints (through dovetail, half blind dovetail, secret mitered dovetail, and the sliding dovetail), the through dovetail is the most basic method, and a perfect one for hand cutting. Contrary to what seems to be popular belief on the internet, they are not really all that hard.
Do you need to clamp dovetails?
I always make sure the side beieing assembled is down on the surface of the table to avoid splitting. In other words I’m hammering the pin board into the tail board not hammering the tail board onto the pin board. No need for clamps if you dovetails are tight. I will clamp a board that may have bow a little.
