These days, thanks to routers and dovetail bits, even a beginning woodworker can incorporate this joint to enhance the simplest projects. Dovetail bits come in an array of cutting angles—usually 7-14°—and heights (see photo, above), on both 1⁄ 2 ” and 1⁄ 4 ” shanks.
What is the standard angle for a dovetail?
Percy Blandford, who has been writing about woodworking for a long time, writes in “The Woodworker’s Bible” that any angle between 7.5° and 10° is acceptable. The ideal, he says, is 8.5° for softwoods and 7.5° when joining hardwoods.
What is the best dovetail angle?
Although softwoods are more compressible than hardwoods, you needn’t change the dovetail angle to add strength to the joint. Any angle between 7° and 15° will work, regardless of the wood. But stay within that range.
What is the degree of a 1 8 dovetail?
It would be extremely difficult to be able to pick these differences up in your dovetails on a piece of furniture by eye. So in closing your 1:4 Saddle-Tail is for all practical purposes 14 degrees, the 1:6 is close to 10 degrees and the 1:8 is about 7 degrees.
Is 11mm dovetail the same as 3 8?
However, that is not the only difference between the two dovetails. They also have different groove angles as shown below. The 11 mm dovetail has a 60-degree angle, while the 3/8” dovetail has a 45-degree angle.
How do you find the angle of a dovetail slot?
You could take an over or between pins measurements if it’s the male or female part. Take 2 measurements using 2 different diameter pair of pins. Assuming the edges are fairly straight you should be able to deduce the dovetail angle.
What is the difference between English dovetail and French dovetail?
French dovetails have sliding joints and are shorter in height. A piece of furniture with a curved front will always have French dovetails, because English dovetails will not work with that shape.
What are the weaknesses of dovetail?
The disadvantages of dovetail joints are that they can be fairly difficult to mark out and cut, and if they are made badly these joints lose the advantages listed above. Depending on the project, function, and design, there are a number of different types of dovetail joints to choose from.
What is dovetail pitch?
There are different types of dovetail joints. The angle of slope varies according to the wood used, purpose of joint and type of work. Typically the slope is 1:6 for softwoods, and a shallower 1:8 slope for hardwoods. Often a slope of 1:7 is used as a compromise.
What is the difference between a 6 to 1 and 8 to 1 dovetail jig?
Steeper angles like 1:6 give more strength to a joint in softwoods (in theory). The 1:8 angle gives a slimmer look, and because hardwoods are much stronger, it has plenty of hold. 1:8 is my favorite. Here’s how to set a sliding bevel or protractor to the correct dovetail angle (if you don’t have a jig or guide).
What are common dovetail sizes?
What ratio is a 14 degree dovetail?
This 14° marker equates to a ratio of 1:4. When used with thinner stock, the 14° angle results in a better looking joint. This different angle also gives you a slightly stronger dovetail interlock on the thinner material.
What is the slope of a dovetail joint?
There are different types of dovetail joints. The angle of slope varies according to the wood used, purpose of joint and type of work. Typically the slope is 1:6 for softwoods, and a shallower 1:8 slope for hardwoods. Often a slope of 1:7 is used as a compromise.
What ratio is a 14 degree dovetail?
This 14° marker equates to a ratio of 1:4. When used with thinner stock, the 14° angle results in a better looking joint. This different angle also gives you a slightly stronger dovetail interlock on the thinner material.
What are the rules for dovetail joints?
The ‘pins’ are the bits of wood between the tails so there are two half-pins; one each side. The general rule is that they measure half the thickness of timber plus around a mm, so the two dots on the shoulder line are 7mm in from each edge.
What is the most common dovetail ratio?
With regard to what to use, a common recommendation is 1:8 for hardwoods and 1:6 for softwoods. These recommendations are based on some arguments related to strength. However, people use a lot of different ratios depending on application and aesthetics.
What is the difference between Picatinny and dovetail?
The Picatinny rail system is a more simple affair. It is a standard width and angle that manufacturers around the world all produce. The angle is 45 degrees as opposed to the 30 degrees that dovetails are regardless of their width. Some rifles come with an integral Picatinny rail machined into the receiver.
What is the weakest wood joint?
A butt joint uses a simple technique whereby two pieces of material are joined together at their ends, without any special shaping or cutting. Although it is simple, the butt joint is also the weakest of the wood joinery types.
When did they stop using dovetail?
Hand-cut dovetailing was the default until 1860 when uniform machine-cut joints were introduced. But fine cabinetmakers persisted in fitting their joints by hand until the early 1900s, and cabinetmakers in Europe cut dovetails by hand well into the 1930s.
What are the different dovetail angles?
Lower (7° to 9°) angles are often advised for joining hardwoods, while higher angles (10° to 14°) are recommended for softwoods and even higher angles (14° to 18°) for half-blind dovetails.
How tight should dovetails be?
If you can use your fist as a hammer to nudge them together, they’re just right. By the way, when you realize they will fit nice and snug, (hopefully by the time they are less than half way down) take them apart and don’t put them together again until you glue them.
What is the angle of a large dovetail?
Angles used on dovetails On large industrial scale machines the angle is usually 45º. For smaller dovetails the usual angle is 60º. Any less than this, i.e. 60° on a small machine, complicates the design of the adjustment mechanism. The angle produced is set by the dovetail cutter used.
What is the main wood joinery method dovetail?
Sliding dovetail joints function by joining two boards at a right angle, with the side of one wooden board cut into a tail. The other wooden board needs to have a socket cut into it away from the edge of the board. The two pieces interlock when you slide the tail into the socket.
What is the strongest joint in woodworking?
While there are many adequately strong ways to join wood, a properly executed mortise-and-tenon joint is the strongest option.
What size chisels for dovetails?
After years of dovetailing, I noticed that two of my chisels were seeing almost all the action: the 1/4″-wide and a 3/4″-wide tools. I use the narrow one for removing waste between the tails and the larger one for removing waste between pins.
What is the best router dovetail jig?
A popular and highly-rated dovetail jig recommended by woodworkers is the LEIGH Box Joint & Beehive Router B975. It’s made to simplify and expedite the process of making box joints and beehive joints with pinpoint accuracy. Stock up to 13/16-inch thick and 9-¼ inch wide can be run through the B975 model.
