Your tails should be around 18mm > 35mm for fine work like drawers and 35mm > 55mm on larger work like a chest. Decide on your tail size remembering “One more tail than pin”. I have a distance between half pins of 330mm and I have chosen a pin size of 10mm. Set dividers to 1 tail +1 pin.there are three or four measurements that define the dimensions of a dovetail slot: the opening and end widths, shoulder angle and depth of cut. The width of a female dovetail slot is measured along the long axis of the barrel at the bottom of the slot, the widest fore and aft point of the dovetail.
What are the measurements for a dovetail joint?
Dovetail Dado Wood Joints have joint widths of 2/3 and joint depths of 1/2. Wood joints are typically used in wood members with widths between 1.5”-3.5” (3.8-8.9 cm) and depths between of . 75”-3.5” (1.9-8.9 cm).
How is a dovetail measured?
Dovetail slides that must be machined accurately to a given width are commonly gaged by using a gage pin of known diameter and measured as indicated by the dimensions x and y.
What size are standard dovetails?
Dovetails come in several different types and sizes depending on manufacturer, but the most common are the 11 mm and 3⁄8 inch (9.5 mm). Some other less known, but currently commercially available dovetail mounts, are 12, 13, 13.5, 14, 14.5, 16, 16.5, 17 and 19 mm.
What are the proportions of a dovetail?
Dovetail angles are usually expressed as ratios — the most common being 1:6 and 1:8 (said “one in eight,” and also written as 6:1 or 8:1). As a general rule of thumb: Use 1:6 for softwoods. Use 1:8 for hardwoods.
What are the measurements for a dovetail joint?
Dovetail Dado Wood Joints have joint widths of 2/3 and joint depths of 1/2. Wood joints are typically used in wood members with widths between 1.5”-3.5” (3.8-8.9 cm) and depths between of . 75”-3.5” (1.9-8.9 cm).
How is a dovetail measured?
Dovetail slides that must be machined accurately to a given width are commonly gaged by using a gage pin of known diameter and measured as indicated by the dimensions x and y.
What are the rules for a dovetail joint?
The ‘pins’ are the bits of wood between the tails so there are two half-pins; one each side. The general rule is that they measure half the thickness of timber plus around a mm, so the two dots on the shoulder line are 7mm in from each edge.
Are 3 8 and 11mm dovetail the same?
However, that is not the only difference between the two dovetails. They also have different groove angles as shown below. The 11 mm dovetail has a 60-degree angle, while the 3/8” dovetail has a 45-degree angle.
Is dovetail 11mm?
The standard 22 tip-off dovetail in the US is 3/8″ at the bottom and up to 1/2″ at the top. The European 11mm dovetail is typically 11mm at the top and perhaps 8mm at the bottom. The 11mm dovetail typically has a 60 degree angle from the bottom inside corner to the top where the 3/8″ is typically 45 degrees.
What is a standard dovetail?
A series of pins cut to extend from the end of one board interlock with a series of ‘tails’ cut into the end of another board. The pins and tails have a trapezoidal shape. Once glued, a wooden dovetail joint requires no mechanical fasteners.
What is the standard angle for a dovetail?
Answer from the experts: Clearly, there’s no shortage of advice about the “best” dovetail angle: Some woodworkers recommend using 12° for “coarse work” and 7° to 10° for decorative joints.
What is the most popular dovetail joint?
Single-lap Dovetail The single-lap (known to many folks as a half-blind dovetail) is the best known of the dovetails since it’s used to join the front to the sides of a drawer.
How do you identify a dovetail joint?
This joint type has two parts, called pins and tails. You can tell the difference between these two pieces because the tails are flared triangular shapes, while the pins are thinner. The tails, which look like those of a dove, are what give the dovetail joint its name.
What is a 6 to 1 dovetail?
The left-hand photo shows the “ratio” method to layout the angle of your dovetails. (I used SketchUp to draw and show the angles.) A 1:6 ratio – that’s one unit horizontal with six matching units drawn vertical – lays out as a 9.5 degree angle.
How tight should dovetail joints be?
If you can use your fist as a hammer to nudge them together, they’re just right. By the way, when you realize they will fit nice and snug, (hopefully by the time they are less than half way down) take them apart and don’t put them together again until you glue them.
What is the spacing for a dovetail joint?
What is the standard angle for a dovetail?
Answer from the experts: Clearly, there’s no shortage of advice about the “best” dovetail angle: Some woodworkers recommend using 12° for “coarse work” and 7° to 10° for decorative joints.
What is a standard dovetail?
A series of pins cut to extend from the end of one board interlock with a series of ‘tails’ cut into the end of another board. The pins and tails have a trapezoidal shape. Once glued, a wooden dovetail joint requires no mechanical fasteners.
What is the ratio of tail to pin in a dovetail joint?
The line between that end point and starting point will be the angle of your tail and pin sides. 6:1 (9.5°) and 8:1 (7.1°) dovetail ratios are the most common (though you’ll often see 4:1 and 10:1 as well).
What are the measurements for a dovetail joint?
Dovetail Dado Wood Joints have joint widths of 2/3 and joint depths of 1/2. Wood joints are typically used in wood members with widths between 1.5”-3.5” (3.8-8.9 cm) and depths between of . 75”-3.5” (1.9-8.9 cm).
How is a dovetail measured?
Dovetail slides that must be machined accurately to a given width are commonly gaged by using a gage pin of known diameter and measured as indicated by the dimensions x and y.
What is the minimum thickness for a dovetail?
Structurally I have looked for pin strength in dovetails as the dovetailed aspect is always strong because it is always at least as wide and mostly wider than the pins. In my own work I aim for a minimum size of 1/4″ and mostly 3/8″.
Should dovetail joints be glued?
Michael Dresdner: The only areas that require glue on dovetails are the diagonal faces. All the diagonal faces are long grain, all the square faces are end grain, and all the flat faces abut end grain. Therefore, you need only apply glue to the diagonal faces on the tails or pins, or both.
What is an English dovetail joint?
A dovetail joint is a locking joint. The English dovetail construction tends to allow for the largest possible drawer storage capacity. French dovetail construction is used for more elaborate features such a curved, bowed design.
What is the most common dovetail ratio?
With regard to what to use, a common recommendation is 1:8 for hardwoods and 1:6 for softwoods. These recommendations are based on some arguments related to strength. However, people use a lot of different ratios depending on application and aesthetics.
