Your tails should be around 18mm > 35mm for fine work like drawers and 35mm > 55mm on larger work like a chest. Decide on your tail size remembering “One more tail than pin”. I have a distance between half pins of 330mm and I have chosen a pin size of 10mm. Set dividers to 1 tail +1 pin.Dovetails come in several different types and sizes depending on manufacturer, but the most common are the 11 mm and 3⁄8 inch (9.5 mm). Some other less known, but currently commercially available dovetail mounts, are 12, 13, 13.5, 14, 14.5, 16, 16.5, 17 and 19 mm.
What are the proportions of a dovetail?
Dovetail angles are usually expressed as ratios — the most common being 1:6 and 1:8 (said “one in eight,” and also written as 6:1 or 8:1). As a general rule of thumb: Use 1:6 for softwoods. Use 1:8 for hardwoods.
What size are standard dovetails?
Dovetails come in several different types and sizes depending on manufacturer, but the most common are the 11 mm and 3⁄8 inch (9.5 mm). Some other less known, but currently commercially available dovetail mounts, are 12, 13, 13.5, 14, 14.5, 16, 16.5, 17 and 19 mm.
How do you calculate dovetails?
An industry standard in some spheres is to have half pins and full pins. so with our current scenario of 3″ we would have 2 x 3/16″ = 3/8″ plus the full pin of 3/8″ so 3/4″ pin accumulation. This then leaves 2 1/4″ for two tails so 1 1/8″ dovetails.
How do you dimension a dovetail?
To obtain dimension x for measuring male dovetails, add 1 to the cotangent of one-half the dovetail angle α, multiply by diameter D of the rods used, and add the product to dimension α.
How do you calculate dovetails?
An industry standard in some spheres is to have half pins and full pins. so with our current scenario of 3″ we would have 2 x 3/16″ = 3/8″ plus the full pin of 3/8″ so 3/4″ pin accumulation. This then leaves 2 1/4″ for two tails so 1 1/8″ dovetails.
How do you dimension a dovetail?
To obtain dimension x for measuring male dovetails, add 1 to the cotangent of one-half the dovetail angle α, multiply by diameter D of the rods used, and add the product to dimension α.
What is a standard dovetail?
Standard dovetail joints have evenly spaced cut pins and tails, traditional dovetails have wide-cut pins and smaller tails. Standard cut pins and tails offer more strength in the drawer, traditional is not quite so strong but are often specified because of their traditional finish.
What are the rules for dovetail joints?
The ‘pins’ are the bits of wood between the tails so there are two half-pins; one each side. The general rule is that they measure half the thickness of timber plus around a mm, so the two dots on the shoulder line are 7mm in from each edge.
Is 3 8 and 11mm dovetail the same?
However, that is not the only difference between the two dovetails. They also have different groove angles as shown below. The 11 mm dovetail has a 60-degree angle, while the 3/8” dovetail has a 45-degree angle.
What is 11mm dovetail?
The standard 22 tip-off dovetail in the US is 3/8″ at the bottom and up to 1/2″ at the top. The European 11mm dovetail is typically 11mm at the top and perhaps 8mm at the bottom. The 11mm dovetail typically has a 60 degree angle from the bottom inside corner to the top where the 3/8″ is typically 45 degrees.
What ratio is a 14 degree dovetail?
Commonly accepted ratios are 1:8 for hardwoods and 1:6 for softer timber. This 14° marker equates to a ratio of 1:4. When used with thinner stock, the 14° angle results in a better looking joint.
How long should dovetails be?
That said, 3/8” gives me room for a drawer bottom groove and enough meat on the drawer sides to compensate for wear and support to the drawer bottom. I then work out how many tails I want. Usually I like tails to be between 1” and 1 ¼” on projects reliant on dovetails more for strength than aesthetics.
How deep should dovetails be?
Try to keep the depth of the dovetail groove between 1/3 and 1/2 the thickness of the part. For example, if the gable of a chest of drawers is 3/4″ thick, machine the dovetail groove between 1/4″ and 3/8″ deep. Any deeper and you will weaken the gable too much.
What are proper dovetail angles?
Percy Blandford, who has been writing about woodworking for a long time, writes in “The Woodworker’s Bible” that any angle between 7.5° and 10° is acceptable. The ideal, he says, is 8.5° for softwoods and 7.5° when joining hardwoods.
What size chisels for dovetails?
After years of dovetailing, I noticed that two of my chisels were seeing almost all the action: the 1/4″-wide and a 3/4″-wide tools. I use the narrow one for removing waste between the tails and the larger one for removing waste between pins.
What ratio is a 14 degree dovetail?
Commonly accepted ratios are 1:8 for hardwoods and 1:6 for softer timber. This 14° marker equates to a ratio of 1:4. When used with thinner stock, the 14° angle results in a better looking joint.
What is the ratio of tail to pin in a dovetail joint?
The line between that end point and starting point will be the angle of your tail and pin sides. 6:1 (9.5°) and 8:1 (7.1°) dovetail ratios are the most common (though you’ll often see 4:1 and 10:1 as well).
What are proper dovetail angles?
Percy Blandford, who has been writing about woodworking for a long time, writes in “The Woodworker’s Bible” that any angle between 7.5° and 10° is acceptable. The ideal, he says, is 8.5° for softwoods and 7.5° when joining hardwoods.
What are typical dovetail angles?
Although softwoods are more compressible than hardwoods, you needn’t change the dovetail angle to add strength to the joint. Any angle between 7° and 15° will work, regardless of the wood. But stay within that range. If you go below 7°, you’ll start to lose the mechanical strength of the dovetail.
How do you calculate dovetails?
An industry standard in some spheres is to have half pins and full pins. so with our current scenario of 3″ we would have 2 x 3/16″ = 3/8″ plus the full pin of 3/8″ so 3/4″ pin accumulation. This then leaves 2 1/4″ for two tails so 1 1/8″ dovetails.
How do you dimension a dovetail?
To obtain dimension x for measuring male dovetails, add 1 to the cotangent of one-half the dovetail angle α, multiply by diameter D of the rods used, and add the product to dimension α.
What is the most popular dovetail joint?
Single-lap Dovetail The single-lap (known to many folks as a half-blind dovetail) is the best known of the dovetails since it’s used to join the front to the sides of a drawer.
Should dovetail joints be glued?
Michael Dresdner: The only areas that require glue on dovetails are the diagonal faces. All the diagonal faces are long grain, all the square faces are end grain, and all the flat faces abut end grain. Therefore, you need only apply glue to the diagonal faces on the tails or pins, or both.
What size dividers for dovetails?
I recommend using two dividers for marking dovetails: one to mark the half pins and one to mark the full tails. I prefer the 4″dividers because I find them more comfortable to use than the larger sizes. In addition to dovetails you will find lots of uses for dividers.
What size is a through dovetail joint?
Through Dovetail Wood Joints have 2 to 4 joints and full joint depths. Wood joints are typically used in wood members with widths between . 75”-1.5” (1.9-3.8 cm) and depths between of 1.5”-3.5” (3.8-8.9 cm).
