It depends on the application. For box joint, some people put a lot more fingers than it is possible to do with Dovetail. In this case, the gluing surface is larger, and the joint is likely stronger. Also, some find a way to hide a finish nail in the joint.
Is dovetail the strongest joint?
The advantages of the dovetail joint are that it is the strongest of all joints, has a large gluing area, is interlocking, resists being pulled apart, looks attractive, and would hold together even without glue.
Is a box joint strong?
Whether you’re making a jewelry box, desk drawer or toy chest, the classic box joint creates sturdy and strong corners. If you’re making boxes for a woodworking project, the classic box joint is a great choice for crafting corners that are as strong and tight as they are aesthetically pleasing.
What is the best joint for a box?
Dovetail joints are most commonly used to create drawer boxes and are typically reserved for higher end projects. It’s common for half-blind dovetails to be used for drawers and through dovetails to be used for boxes and cases.
Is dovetail the highest quality?
Dovetail is used primarily in drawers and is a strong indicator of quality craftsmanship while rabbet joints provide critical support for the corners of cabinet pieces and shelving. Good quality furniture will make use of both of these woodworking joints when they’re needed during the construction.
Is a box joint strong?
Whether you’re making a jewelry box, desk drawer or toy chest, the classic box joint creates sturdy and strong corners. If you’re making boxes for a woodworking project, the classic box joint is a great choice for crafting corners that are as strong and tight as they are aesthetically pleasing.
What is the weakest joint in carpentry?
A butt joint uses a simple technique whereby two pieces of material are joined together at their ends, without any special shaping or cutting. Although it is simple, the butt joint is also the weakest of the wood joinery types.
What is the strongest type of joint?
Mortise and tenon joints have stood the test of time for their remarkable strength. This traditional joint involves a projecting piece of wood, called a tenon, securely fitting into a corresponding cavity, a mortise.
What are the cons of a box joint?
Box joint cons: The joint makes it very difficult to remove and then replace a cupped or rotted single board in the box. Once glued you are not likely to get this joint apart for repairing a single side of the box. Typically you’ll end up destroying the other two boards that the board you want to replace attaches to.
What are box joints good for?
Applications include all sorts of wooden boxes and carcasses. While primarily used for right angle joints it can also be used for hexagonal boxes and other unusual shapes. It is used for the sides of drawers and lids, but not, in general, for joining thin panels to structural members.
Should box joints be glued?
Joints that are cut properly should come together smoothly. The big advantage of box joints is the large amount of gluing surface the interlocking fingers create. So it only takes a small amount of glue to create a rock-solid joint. In fact you don’t need to put glue on every surface.
How deep should a box joint be?
The slot width will be how wide your finished joints are. The depth of the slot should be a little less than the thickness of the wood you will use. I use a 1/2″ dado for 3/4″ thick wood.
Are box joints hard to make?
With their rows of evenly spaced pins, box joints have a traditional, almost old-fashioned appeal. Box joints aren’t just good looking. They’re also very strong. And box joints are simple to cut — all you need is a table saw. With all that box joints have going for them, they sound like the perfect joint.
How tight should a box joint be?
Re: box joints too tight The parts should slide together with minor pressure. Once the glue gets put on they swell and you will never get them together if they are too tight.
Is a dovetail joint strong or weak?
Dovetail joints are known for their inherent strength and resistance to being pulled apart (tensile strength).
When did they stop using dovetail?
By 1730, through dovetail joinery was abandoned in English furniture making in favor of the lapped construction. As furniture became more refined, furniture makers began to take pride in the construction of their drawers as well.
Should you glue dovetail joints?
Michael Dresdner: The only areas that require glue on dovetails are the diagonal faces. All the diagonal faces are long grain, all the square faces are end grain, and all the flat faces abut end grain. Therefore, you need only apply glue to the diagonal faces on the tails or pins, or both.
Is a dovetail joint strong or weak?
Dovetail joints are known for their inherent strength and resistance to being pulled apart (tensile strength).
Is dovetail joint permanent?
The strongest and most permanent right-angled joints made in wood are the ‘dove-tail’ joints, as illustrated below. The so-called tails and pins fit together to form a secure joint.
What is the strongest way to join two pieces of wood together?
Mortise and Tenon Joint Mortise and tenon joints are a classic method of wood joinery known for both strength and elegance. A peg, or tenon, is cut into the end of one board to fit snugly into a hole, or mortise, on the adjoining piece of stock for a strong joint.
When did they stop using dovetail joints?
By 1730, through dovetail joinery was abandoned in English furniture making in favor of the lapped construction. As furniture became more refined, furniture makers began to take pride in the construction of their drawers as well.
Is a box joint strong?
Whether you’re making a jewelry box, desk drawer or toy chest, the classic box joint creates sturdy and strong corners. If you’re making boxes for a woodworking project, the classic box joint is a great choice for crafting corners that are as strong and tight as they are aesthetically pleasing.
What is the strongest way to join two pieces of wood together?
Mortise and Tenon Joint Mortise and tenon joints are a classic method of wood joinery known for both strength and elegance. A peg, or tenon, is cut into the end of one board to fit snugly into a hole, or mortise, on the adjoining piece of stock for a strong joint.
Which is the oldest and strongest kind of wood joint?
The oldest, strongest joint in woodworking, and metalworking without doubt. It is considered the most appropriate method of joining two pieces of wood together crossways.
Which type of wood joint is the oldest and strongest wood joint?
A mortise and tenon joint is the oldest and strongest type of joint used in woodworking. It is made up of two different component parts: a mortise and a tenon. It is usually used to connect two pieces of wood at a 90-degree angle.
What is the most difficult woodworking joint?
The dovetail is beautiful and strong, but among the most difficult joints to execute.
