There should be roughly one dovetail each 25mm or so across the width. There’s no hard and fast rule so it’s up to the woodworker to use his or her judgement to decide how many are needed. The wood here is 92mm wide and as a consequence I’m going to have three dovetails.
How big should dovetails be?
For drawers, boxes or trays 2″ or less I generally like a single dovetail. For 3″ to 3 1/2″ and less two dovetails, for 4″ three dovetails, for 5″ to 6″ four dovetails and for 6″ four or possibly five.
What size are standard dovetails?
Dovetails come in several different types and sizes depending on manufacturer, but the most common are the 11 mm and 3⁄8 inch (9.5 mm). Some other less known, but currently commercially available dovetail mounts, are 12, 13, 13.5, 14, 14.5, 16, 16.5, 17 and 19 mm.
What dovetail ratio is best?
Dovetail angles are usually expressed as ratios — the most common being 1:6 and 1:8 (said “one in eight,” and also written as 6:1 or 8:1). As a general rule of thumb: Use 1:6 for softwoods. Use 1:8 for hardwoods.
What size dovetail chisels do you really need?
Chisel Sizes – – 12mm / 1/2″ – This will do the majority of your morticing, and come in when cleaning out the pins on those dovetails. – 19mm / 3/4″ (or above) – A nice wide chisel is very useful, and I’d probably aim at an inch, though somewhere between 3/4″ – 1 1/4″ will fit the bill.
How big should dovetails be?
For drawers, boxes or trays 2″ or less I generally like a single dovetail. For 3″ to 3 1/2″ and less two dovetails, for 4″ three dovetails, for 5″ to 6″ four dovetails and for 6″ four or possibly five.
What are the rules for dovetail joints?
The general rule is that they measure half the thickness of timber plus around 1 mm along the shoulder line. So these two awl dots are 7 mm in from each edge. These two dots, which mark the corners of the half pins, are now converted into a 1:8 slope at each side.
What is a standard dovetail?
The dovetail joint drawers are typically used to link the edges of a drawer to the front and are known for their tensile strength to being pushed apart. Pins or tongues cut from one board’s end interlock with the groove or tail on the other board’s end.
Are 3 8 and 11mm dovetail the same?
However, that is not the only difference between the two dovetails. They also have different groove angles as shown below. The 11 mm dovetail has a 60-degree angle, while the 3/8” dovetail has a 45-degree angle.
What is the most popular dovetail joint?
Single-lap Dovetail The single-lap (known to many folks as a half-blind dovetail) is the best known of the dovetails since it’s used to join the front to the sides of a drawer.
What is the common dovetail ratio?
Anything from 1:6 to 1:9 looks good and works well. Too little rise leaves corners with short grain that easily breaks off, too much rise looks like a poorly made box joint. As long as it looks good, and assembles without breaking, its a good joint.
Are dovetail joints worth it?
Dovetail drawers are known for their durability. The joint’s design provides exceptional resistance to the stresses of heavy items, making them ideal for storing dishes, pots, and pans. The construction of dovetail drawers ensures that they will not come apart easily, even with frequent use.
Which is better English or French dovetail?
While both English and French dovetail construction are very sturdy and high quality, English dovetail construction is slightly sturdier with the trade-off of being more expensive and time-consuming to produce.
Are dovetail chisels worth it?
The triangular cross-section of these chisels make them ideal for paring and chopping away the waste on dovetail joinery. Suitable for other joinery tasks, these affordable chisels are a nice complement to standard bench chisels for creating and fine-tuning joinery.
How thick should a dovetail jig be?
Use the jig to cut half blind dovetails for drawer construction, as well as precise comb or finger joints. Cutting up to 28mm thick material, the jig is ideally suited to utility furniture. It will also cut through dovetails, in material up to 19mm which is great for projects such as toolboxes.
Which chisel is best for dovetails?
Fishtail Chisels are perfect for reaching the back corners of half-blind dovetails and paring other hard-to-reach areas. Their unique shape offers versatility for right and left hand recesses.
What is the standard dovetail ratio?
With regard to what to use, a common recommendation is 1:8 for hardwoods and 1:6 for softwoods. These recommendations are based on some arguments related to strength. However, people use a lot of different ratios depending on application and aesthetics.
How deep should dovetails be?
But keep in mind that if you machine the dovetail groove across the work piece you will be weakening it because you are removing some of its thickness. Try to keep the depth of the dovetail groove between 1/3 and 1/2 the thickness of the part.
How thick should a dovetail jig be?
Use the jig to cut half blind dovetails for drawer construction, as well as precise comb or finger joints. Cutting up to 28mm thick material, the jig is ideally suited to utility furniture. It will also cut through dovetails, in material up to 19mm which is great for projects such as toolboxes.
How big should dovetails be?
For drawers, boxes or trays 2″ or less I generally like a single dovetail. For 3″ to 3 1/2″ and less two dovetails, for 4″ three dovetails, for 5″ to 6″ four dovetails and for 6″ four or possibly five.
Should you glue dovetail joints?
Michael Dresdner: The only areas that require glue on dovetails are the diagonal faces. All the diagonal faces are long grain, all the square faces are end grain, and all the flat faces abut end grain. Therefore, you need only apply glue to the diagonal faces on the tails or pins, or both.
How do you calculate dovetail joints?
What is the weakness of dovetail joint?
The disadvantages of dovetail joints are that they can be fairly difficult to mark out and cut, and if they are made badly these joints lose the advantages listed above. Depending on the project, function, and design, there are a number of different types of dovetail joints to choose from.
What is an English dovetail joint?
A dovetail joint is a locking joint. The English dovetail construction tends to allow for the largest possible drawer storage capacity. French dovetail construction is used for more elaborate features such a curved, bowed design.
How deep should dovetails be?
But keep in mind that if you machine the dovetail groove across the work piece you will be weakening it because you are removing some of its thickness. Try to keep the depth of the dovetail groove between 1/3 and 1/2 the thickness of the part.
What is the strongest joint in woodworking?
A mortice and tenon joint is generally recognised as the toughest around. As a result, they are sensible to use for commercial joinery projects. In simple terms, it allows two pieces of wood to be connected together.
