What is the most common dovetail pitch?

Percy Blandford, who has been writing about woodworking for a long time, writes in his new book, “The Woodworker’s Bible,” that any angle between 7.5° and 10° is acceptable. The ideal, he says, is 8.5° for softwoods and 7.5° when joining hardwoods. One Wednesday morning I laid out and cut a bunch of these dovetails.Most commonly, woodworkers design their joinery using either a 1:6 or 1:8 dovetail angle.

What is a standard dovetail?

The dovetail joint drawers are typically used to link the edges of a drawer to the front and are known for their tensile strength to being pushed apart. Pins or tongues cut from one board’s end interlock with the groove or tail on the other board’s end.

What is the most popular dovetail joint?

The through dovetail joint is the most popular dovetail joint because it is strong, attractive, and versatile. It is commonly used in furniture-making, cabinetry, and woodworking. The through dovetail joint is a traditional woodworking joint characterized by the interlocking triangular shape it creates.

What is the degree of a dovetail angle?

Although softwoods are more compressible than hardwoods, you needn’t change the dovetail angle to add strength to the joint. Any angle between 7° and 15° will work, regardless of the wood. But stay within that range. If you go below 7°, you’ll start to lose the mechanical strength of the dovetail.

What dovetail ratio is best?

Dovetail angles are usually expressed as ratios — the most common being 1:6 and 1:8 (said “one in eight,” and also written as 6:1 or 8:1). As a general rule of thumb: Use 1:6 for softwoods. Use 1:8 for hardwoods.

Is 11mm dovetail the same as 3 8?

However, that is not the only difference between the two dovetails. They also have different groove angles as shown below. The 11 mm dovetail has a 60-degree angle, while the 3/8” dovetail has a 45-degree angle.

What are common dovetail sizes?

Dovetails come in several different types and sizes depending on manufacturer, but the most common are the 11 mm and 3⁄8 inch (9.5 mm). Some other less known, but currently commercially available dovetail mounts, are 12, 13, 13.5, 14, 14.5, 16, 16.5, 17 and 19 mm.

Which is better English or French dovetail?

While both English and French dovetail construction are very sturdy and high quality, English dovetail construction is slightly sturdier with the trade-off of being more expensive and time-consuming to produce.

What is an English dovetail joint?

A dovetail joint is a locking joint. The English dovetail construction tends to allow for the largest possible drawer storage capacity. French dovetail construction is used for more elaborate features such a curved, bowed design.

What is the common dovetail ratio?

Anything from 1:6 to 1:9 looks good and works well. Too little rise leaves corners with short grain that easily breaks off, too much rise looks like a poorly made box joint. As long as it looks good, and assembles without breaking, its a good joint.

What is angle 1 to 8 dovetail?

A 1:8 ratio – one unit horizontal with eight matching units drawn vertical – is an angle of 7.1 degrees.

What ratio is a 14 degree dovetail?

This 14° marker equates to a ratio of 1:4. When used with thinner stock, the 14° angle results in a better looking joint. This different angle also gives you a slightly stronger dovetail interlock on the thinner material.

What are the weaknesses of dovetail?

The disadvantages of dovetail joints are that they can be fairly difficult to mark out and cut, and if they are made badly these joints lose the advantages listed above. Depending on the project, function, and design, there are a number of different types of dovetail joints to choose from.

How deep should a dovetail joint be?

so with our current scenario of 3″ we would have 2 x 3/16″ = 3/8″ plus the full pin of 3/8″ so 3/4″ pin accumulation. This then leaves 2 1/4″ for two tails so 1 1/8″ dovetails. As I said, for me, generally, I simply use 3/8″ equally for all of my pins as my standard size in my more general work.

What is the slope of a dovetail joint?

There are different types of dovetail joints. The angle of slope varies according to the wood used, purpose of joint and type of work. Typically the slope is 1:6 for softwoods, and a shallower 1:8 slope for hardwoods. Often a slope of 1:7 is used as a compromise.

What is the standard dovetail ratio?

With regard to what to use, a common recommendation is 1:8 for hardwoods and 1:6 for softwoods. These recommendations are based on some arguments related to strength. However, people use a lot of different ratios depending on application and aesthetics.

What is an English dovetail joint?

A dovetail joint is a locking joint. The English dovetail construction tends to allow for the largest possible drawer storage capacity. French dovetail construction is used for more elaborate features such a curved, bowed design.

What is a simple dovetail joint?

The simple dovetail neck joint is a timeless design that consists of a dovetail-shaped projection on the neck fitting into a corresponding recess in the guitar body. This joint provides a secure connection, facilitating good tonal transfer between the neck and body.

Are dovetail joints difficult?

This is a relatively complex joint that takes time to fit together. But it’s absolutely within the capabilities of anyone who knows how to use a hand saw. In my opinion, the hardest part is cutting the sides of the pins and tails accurately. Luckily, this is made a lot easier with a good dovetail jig.

What size chisels for dovetails?

After years of dovetailing, I noticed that two of my chisels were seeing almost all the action: the 1/4″-wide and a 3/4″-wide tools. I use the narrow one for removing waste between the tails and the larger one for removing waste between pins.

Is a box joint stronger than a dovetail?

It depends on the application. For box joint, some people put a lot more fingers than it is possible to do with Dovetail. In this case, the gluing surface is larger, and the joint is likely stronger. Also, some find a way to hide a finish nail in the joint.

Are dovetail joints worth it?

Making sure that you pick a drawer joint that can withstand this type of wear and tear is crucial to the longevity of your kitchen cabinets. Dovetail joints are considered one of the strongest joints used in kitchen cabinetry construction and are the best solution for a kitchen cabinet drawer box.

When did they stop using dovetail?

Hand-cut dovetailing was the default until 1860 when uniform machine-cut joints were introduced. But fine cabinetmakers persisted in fitting their joints by hand until the early 1900s, and cabinetmakers in Europe cut dovetails by hand well into the 1930s.

What is the strongest joint in woodworking?

A mortice and tenon joint is generally recognised as the toughest around. As a result, they are sensible to use for commercial joinery projects. In simple terms, it allows two pieces of wood to be connected together.

Do dovetail joints need glue?

Michael Dresdner: The only areas that require glue on dovetails are the diagonal faces. All the diagonal faces are long grain, all the square faces are end grain, and all the flat faces abut end grain. Therefore, you need only apply glue to the diagonal faces on the tails or pins, or both.

What is the main wood joinery method dovetail?

Sliding dovetail joints function by joining two boards at a right angle, with the side of one wooden board cut into a tail. The other wooden board needs to have a socket cut into it away from the edge of the board. The two pieces interlock when you slide the tail into the socket.

Mike Walker

Repair and Construction Expert. WoodiesDIY.tv Owner