Dovetail angles are usually expressed as ratios — the most common being 1:6 and 1:8 (said “one in eight,” and also written as 6:1 or 8:1). As a general rule of thumb: Use 1:6 for softwoods. Use 1:8 for hardwoods.
What is the best ratio for dovetails?
With regard to what to use, a common recommendation is 1:8 for hardwoods and 1:6 for softwoods. These recommendations are based on some arguments related to strength. However, people use a lot of different ratios depending on application and aesthetics.
What is the standard size of a dovetail?
11 mm and 3/8” dovetails are the two most common types of dovetails that you can find on rifles. The 11 mm dovetail represents a standard in Europe, while the 3/8” is a standard in the USA.
What is the most common dovetail angle?
Percy Blandford, who has been writing about woodworking for a long time, writes in his new book, “The Woodworker’s Bible,” that any angle between 7.5° and 10° is acceptable. The ideal, he says, is 8.5° for softwoods and 7.5° when joining hardwoods.
What is the best ratio for dovetails?
With regard to what to use, a common recommendation is 1:8 for hardwoods and 1:6 for softwoods. These recommendations are based on some arguments related to strength. However, people use a lot of different ratios depending on application and aesthetics.
What is the most common dovetail angle?
Percy Blandford, who has been writing about woodworking for a long time, writes in his new book, “The Woodworker’s Bible,” that any angle between 7.5° and 10° is acceptable. The ideal, he says, is 8.5° for softwoods and 7.5° when joining hardwoods.
What makes a dovetail joint so strong?
Methods. The dovetail joint is very strong because of the way the ‘tails’ and ‘pins’ are shaped. This makes it difficult to pull the joint apart and virtually impossible when glue is added.
What are the rules for dovetails?
What is the minimum thickness for a dovetail?
Structurally I have looked for pin strength in dovetails as the dovetailed aspect is always strong because it is always at least as wide and mostly wider than the pins. In my own work I aim for a minimum size of 1/4″ and mostly 3/8″.
Is dovetail the highest quality?
Dovetail is arguably the strongest joint in millwork. It’s made so that it can’t be twisted or pulled in any direction except for one. This means that it’ll take more force to break or damage the joint.
What are the traditional dovetail angles?
The angle of a dovetail joint should be between 7 and 15 degrees: too broad and the joint won’t be strong enough, too skinny, and the pin can snap. So the angle of the dovetail mainly depends on the use and wear the joint will get. 5. They are called ‘dovetails’ because they are shaped like the tail feathers of a dove!
What are the weaknesses of dovetail?
The disadvantages of dovetail joints are that they can be fairly difficult to mark out and cut, and if they are made badly these joints lose the advantages listed above. Depending on the project, function, and design, there are a number of different types of dovetail joints to choose from.
What is the most popular dovetail joint?
The through dovetail joint is the most popular dovetail joint because it is strong, attractive, and versatile. It is commonly used in furniture-making, cabinetry, and woodworking. The through dovetail joint is a traditional woodworking joint characterized by the interlocking triangular shape it creates.
How deep should a dovetail joint be?
Typically we use 1 ½” – 2” deep dovetails that are about 2” less deep than the joist, and 4” less deep than the girt – but that is just a starting point – the loads and reactions have to be calculated from there.
What is the formula for measuring dovetails?
To obtain dimension x for measuring male dovetails, add 1 to the cotangent of one-half the dovetail angle α, multiply by diameter D of the rods used, and add the product to dimension α.
What is a 3 8 dovetail?
3/8″ dovetail rails, sometimes call tip off rails, consist of two thin parallel grooves and are used almost exclusively on rimfire rifles and air rifles. 3/8″ dovetail rails are a common, standardized style within the rimfire industry and are inexpensive to machine into the firearm’s frame.
What is the minimum thickness for a dovetail board?
The minimum recommended pin board thickness is 1⁄2″[13mm]. Remember, the No 128 cutters rout at 3⁄8″[9,5mm] deep. If you wish to rout a pin board less than the minimum thickness ➀, it will be necessary to pack the board up from the jig body. We suggest using a piece of 1⁄4″ to 3⁄8″[6 to 9mm] plywood for this purpose ➁.
What is the best ratio for dovetails?
With regard to what to use, a common recommendation is 1:8 for hardwoods and 1:6 for softwoods. These recommendations are based on some arguments related to strength. However, people use a lot of different ratios depending on application and aesthetics.
What is the most common dovetail angle?
Percy Blandford, who has been writing about woodworking for a long time, writes in his new book, “The Woodworker’s Bible,” that any angle between 7.5° and 10° is acceptable. The ideal, he says, is 8.5° for softwoods and 7.5° when joining hardwoods.
How deep should a dovetail joint be?
Typically we use 1 ½” – 2” deep dovetails that are about 2” less deep than the joist, and 4” less deep than the girt – but that is just a starting point – the loads and reactions have to be calculated from there.
What are the 2 types of dovetail joints?
Types of Dovetail Joints Half-Blind dovetails: In these, the pins and tails are hidden. Half-blind dovetails are only revealed when moved, opened or seen from a certain angle, like behind a drawer face. In a through dovetail, both the dovetails and pins are visible.
How deep should dovetails be?
Try to keep the depth of the dovetail groove between 1/3 and 1/2 the thickness of the part. For example, if the gable of a chest of drawers is 3/4″ thick, machine the dovetail groove between 1/4″ and 3/8″ deep. Any deeper and you will weaken the gable too much.
What is the formula for measuring dovetails?
To obtain dimension x for measuring male dovetails, add 1 to the cotangent of one-half the dovetail angle α, multiply by diameter D of the rods used, and add the product to dimension α.
Do you need to glue dovetails?
Michael Dresdner: The only areas that require glue on dovetails are the diagonal faces. All the diagonal faces are long grain, all the square faces are end grain, and all the flat faces abut end grain. Therefore, you need only apply glue to the diagonal faces on the tails or pins, or both.
What is the main wood joinery method dovetail?
Sliding dovetail joints function by joining two boards at a right angle, with the side of one wooden board cut into a tail. The other wooden board needs to have a socket cut into it away from the edge of the board. The two pieces interlock when you slide the tail into the socket.
Is a half blind dovetail joint strong?
Joining drawer sides to drawer fronts using the half-blind joint leaves the front of the drawer without visible joinery while providing great interlocking strength opposing the stresses constantly applied to the drawer when opening and closing.
